manualshive.com logo in svg

NEC ELECTRA ELITE IPK II, Руководство по программированию

Поделиться
Скачать
NEC ELECTRA ELITE IPK II Скачать руководство пользователя страница 455

Document Revision 1

Electra Elite IPK II

2 - 420

Program 47 : In-Mail

07

Recording Conversation Beep

(Rec Conv Beep)

Use this option to enable or disable the 
Conversation Record beep. If enabled, all parties on 
a call will hear the voice prompt Recording followed 
by a single beep when the extension user initiates 
Conversation Record. If disabled, the voice prompt 
and beep will not occur. When you disable the 
Conversation Record beep, the following voice 
prompts do not occur while IPK II In-Mail records the 
conversation:

“Recording” 
(followed by a beep)

“That mailbox is full” 
(if the mailbox message storage capacity is reached)

“You have reached the recording limit” 
(if the recorded message is too long)

The Electra Elite IPK II telephone system software 
provides an additional Conversation Record beep. 
This beep repeats according to the setting of 
Program 45-01-06: Voice Mail Integration 
Options: Record Alert Tone Interval Time 
(0~64800 seconds). To disable the Electra Elite IPK 
II telephone system Conversation Record beep, 
enter 0 for this option.

0 = No (Disabled)

1 = Yes (Enabled)

1 (Yes - Enabled)

08

Message Waiting Lamp

(Update MW Lamp)

Use this option to enable or disable Message 
Waiting lamping at the extension associated with the 
Subscriber mailbox. For Subscriber Mailboxes, you 
should leave this option enabled. For Guest 
Mailboxes, you should leave this option disabled.

0 = No (Disabled)

1 = Yes (Enabled)

1 (Yes - Enabled)

09

Auto Attendant Do Not Disturb

(Auto-ATT DND)

Use this option to enable or disable Auto Attendant 
Do Not Disturb. When a subscriber enables Auto 
Attendant Do Not Disturb, an Automated Attendant 
caller will route directly to the mailbox, hear the 
greeting, and be asked to leave a message. A 
subscriber can also enable Auto Attendant Do Not 
Disturb while recording their mailbox greeting.

0 = No (Disabled)

1 = Yes (Enabled)

0 (No - Disabled)

Input Data 

Item 

No.

Item

Input Data

Default

Содержание ELECTRA ELITE IPK II










































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды