manualshive.com logo in svg

Neat INKA, Техническое руководство

Поделиться
Скачать
Neat INKA Скачать руководство пользователя страница 10

 

INKA, IOR, REPO & LINK 

1.6 Batteries 

 

1.6.1 INKA 

 
INKA is powered by 2 alkaline batteries size AAA (LR03). Depending on the quality of the battery, and 
assuming that no jumpers are mounted on the circuit board inside INKA, the battery lifetime is up to 10 
years when INKA is in power save mode and up to 20 months when INKA is in normal power mode. If 
an AC/DC adapter is used, the batteries are used as a backup in case of power failure.

 

 

1.6.2  IOR, REPO & LINK 

 
IOR, REPO and LINK are powered by an external AC/DC adapter. A rechargeable NiMH battery 
inside the units works as a backup during mains power failure. The unit can run 4 days on the backup 
battery when it is fully charged. 
 

 

1.7 AC/DC Adapter 

 
The AC/DC adapter shall be installed in an ordinary AC mains outlet, European type. The voltage in 
the outlet shall be between 100 V

AC

 and 240 V

AC

. Please use only the specified adapter marked 

“NEAT Electronics” and “PS49/1880”, part number NE31 03001-01. 
 
Connect the adapter to the connector marked DC at the bottom side of the unit, see section 1.2.1-
1.2.4. 
 
 

 

Technical Handbook for the IOR Family (firmware v20.x), document number NE41 06007-02 v1.0 

10

 

Содержание INKA





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды