background image

 

5

INSTRUCTIONS FOR USE 

1.

  Having taken the test hammer from its case, gently push the piston inwards 

pressing it against a stiff surface (held the hammer with both hands when using 
it).  The piston will release itself from its catch and emerge from the body of the 
device which will then be ready for testing. 

Press the piston against the surface of the material to be tested, holding the 
device perpendicularly to the surface.  Gradually apply increasing pressure until 
the mass impact is released.  Keep the device firmly pressed against the surface 
being tested and look at the rebound reading on the scale

.  

Do not touch the 

side button whilst pressing on the piston

.  On removing the device from the 

surface being tested, the piston once more emerges completely from the device 
which is immediately ready for a second test. 

 

2.

  If it is difficult to see the reading under the conditions specified in the previous 

paragraph, 

press the side button only after impact

 

hold the button in 

and 

remove the device in order to read the scale. 

3.

  If the button is used, as in the above case, the piston remains inside the device 

when it is removed from the surface being tested.  In such cases, in order to 
prepare the test hammer for further tests, activate in by the method indicated in 
Paragraph 1.  The position of the device when the piston has withdrawn inside is 
also the position used for packing away the device in its case. 

Содержание W-D-2005


















Отзывы: