background image

- 2 -

Introduction 

EVOTIS is designed to detect defects and quantitatively measure damage of 
composite structured materials. In order to fully realize its performance 
capabilities, please read this operation manual carefully. 

The following general safety precautions must be observed during all phases 
of operation of this instrument. Failure to comply with these precautions or 
with specific warnings elsewhere in this manual may impair the protections 
provided by the equipment. Sysmic Co., Ltd. assumes no liability for the 
customer’s failure to comply with these requirements. 

• Do Not Operate in an Explosive Atmosphere
Do not operate the instrument in the presence of flammable gases or
fumes. Operation of any electrical instrument in such an environment
constitutes a definite safety hazard.

• Keep Away from Live Circuits
Operation personnel must not remove instrument covers. Component
replacement and internal adjustments must be made by qualified
maintenance personnel. Do not replace components with the power cable
connected. Under certain conditions, dangerous voltages may exist even
with the power cable removed. To avoid injuries, always disconnect the
power and discharge circuits before touching them.

• Do Not Substitute Parts or Modify the Instrument
To avoid the danger of introducing additional hazards, do not install
substitute parts or perform any unauthorized modification of the
instrument. Return the instrument to the exporter for service and repair
to ensure that safety features are maintained.

Содержание EVOTIS










Отзывы: