Nav TV ZEN-25 Скачать руководство пользователя страница 3

Fiber Installation in Vehicles with an Existing M.O.S.T. Amplifier

1)

Locate the factory amplifier, push down on the retaining clip and remove the harness containing the M.O.S.T.

 

connector from the amplifier

2)

Gently pry the M.O.S.T. retaining clip towards the outside of the factory connector and pull the male fiber

 

optic out of the factory housing. Be careful not to leave grease or debris on the fiber optic cable ends.

3)

This is what the male fiber optic should look like when removed from the factory harness

4)

Insert the included M.O.S.T. Connector (NTV-CON002) over the factory male fiber optic end

5)

This is what the fiber optic cable should look like once completed.

ZEN-25 Installation

If the vehicle has a factory M.O.S.T. fiber optic amplifier, it must be removed and the ZEN-25 can be installed in its 

place. M.O.S.T. BMW amplifiers are located in the left rear section of the trunk. 

1

2

3

4

 5

1

2

3

4

5

6

ZEN-25 Pin

Color

To Vehicle

1
3
4
6

Yellow

Violet

Black

Blue

12V+ Constant

Not Used

Ground -

remote out +*

Wire Side

1) Connect the following wires from the

provided power harness:

*This 12v+ remote output wire MUST be used for the aftermarket amplifier/DSP remote turn on for proper

functionality. If installing more than one Amp/DSP, a relay must be used for reliable system turn

 on.

2) If using analog RCA outputs for signal to the amplifier, connections are made according to the chart below.

WARNING: Do not connect RCA cables to this interface until all amplifiers /DSP are properly grounded.

Failure to do this may cause damage to the interface and VOID the warranty!

3) If using Toslink for signal to the amplifier, connect the cable to the Toslink port shown on page 2. NOTE: both

analog and digital ouputs are aligned to produce sound simultaneously.

4) Connect the M.O.S.T. fiber optic cable to the M.O.S.T. 25 connector on the ZEN-25 interface.

ZEN-25 Power and Output Signal Wiring

   2 

       3             4 

   5 

      6            7 

 8 

     9         10            11 

  12

Left    Right      Left       Right     Left      Right       Left 

Right      Left        Right    Center     Sub

 Front      Front     Front     Front      Front    Front       Rear     Rear       Rear       Rear

3

Содержание ZEN-25
















Отзывы: