Nautilus Schwinn IC4 Скачать руководство пользователя страница 55

Страница: 55 / 82

Using a #2 Phillips screwdriver, remove the indicated hardware from

the Drive Belt Cover. Carefully remove the Drive Belt Cover and set it

safely aside for reassembly.

Note:

The oval indicates the two machine screws with washers.

Drive Belt Cover

Note:

Please disregard the Right Crank Arm in the above

image. It was removed during an earlier step.

Flywheel Axle Nut

Flywheel Bracket

Tensioner Eyebolt

Tensioner

Support

Bracket

Mark the position of the Flywheel Axle Nut on the Flywheel Bracket.

Also record the number of threads showing on the Tensioner Eyebolt, or

Flywheel Tensioners, on each side of the Tensioner Support Bracket.

To loosen the Flywheel hardware, use a 15mm crescent wrench to

hold the Flywheel Axle Nut on one side steady and loosen the Flywheel

Axle Nut on the opposite side with a 15mm socket and wrench. Remove the

Flywheel Axle Nuts from the Flywheel Axle. Set the hardware safely aside for

reassembly.

Содержание Schwinn IC4



















































































Результаты поиска

Содержание Schwinn IC4

Отзывы:

Похожие инструкции для Schwinn IC4

Бренды по названию

Популярные бренды

Nautilus Schwinn IC4, Руководство по обслуживанию

Результаты поиска

Содержание Schwinn IC4

Отзывы:

Похожие инструкции для Schwinn IC4

Бренды по названию

Популярные бренды