Nautilus Schwinn IC4 Скачать руководство пользователя страница 7

Страница: 7 / 82

Workout with Other Fitness Apps

This fitness machine has integrated Bluetooth

connectivity which allows it to work with a number of fitness

apps. For our latest list of supported apps, please visit:

www.nautilus.com/partners

Bluetooth

Heart Rate Enabled

Your fitness machine is equipped to be able to receive a signal from a Bluetooth

Heart Rate Sensing device. When

connected, the Console will display the Bluetooth

Connected icon. Be sure to follow the described method to sync your

device.

If you have a pacemaker or other implanted electronic device, consult your doctor before using a Bluetooth

strap or other Bluetooth

heart rate monitor.

Bluetooth

Heart Rate Armband

(supplied with the IC4 and C6 machines

only)

Your fitness machine is provided with a Bluetooth

Heart Rate Armband. When the

Bluetooth

Heart Rate Armband is connected, the Console will display the Bluetooth

Connected icon.

If you have a pacemaker or other implanted electronic device, consult your

doctor before using a Bluetooth

armband or other Bluetooth

heart rate

monitor.

The Heart Rate Armband should be worn on the upper portion of your forearm, with the Heart Rate Sensor to the inside of

your forearm. It should be snug enough not to move around on your arm, but not so tight that it restricts blood circulation.

Note:

Be sure to remove the protective cover from the Heart Rate Sensor

before use.

1. Put the Bluetooth

Heart Rate Armband onto the upper portion of your

forearm.

2. Push the On/Off LED button on the Heart Rate Armband to activate it. The

LED will flash blue quickly, indicating that the armband has been activated.

3. The LED will flash blue slowly when a heart rate is detected. The Blue

tooth

Connected icon will activate on the Console when connected. You are ready to workout.

At the end of your workout, push the On/Off LED button to disconnect and deactivate your Heart Rate Armband.

If you press the On/Off LED button and the LED flashes red

several times, the battery is low and should be charged. To

charge the Bluetooth

Heart Rate Armband, connect the

Charging Cable to the Charging Terminals on the inside of the

Sensor. Connect the Charging Cable to a powered USB Port.

The LED will flash red and green while charging. When fully

charged, the LED will be green continuously.

USB Connector

Charging Terminals

Heart Rate Sensor

Armband

Charging Cable

On/Off LED

button

Содержание Schwinn IC4



















































































Результаты поиска

Содержание Schwinn IC4

Отзывы:

Похожие инструкции для Schwinn IC4

Бренды по названию

Популярные бренды

Nautilus Schwinn IC4, Руководство по обслуживанию

Результаты поиска

Содержание Schwinn IC4

Отзывы:

Похожие инструкции для Schwinn IC4

Бренды по названию

Популярные бренды