
XR6/XR3 Troubleshooting Manual
Responding to alarms
Issue 3.0 2009-07-15
Page 1-15
2. If the transmitter successfully switched to the standby exciter, suspect the main exciter's
interphase PDM driver PWB.
3. Use an oscilloscope to measure the voltage at TP6 on the interphase PDM driver PWB. The
indication should have a dc offset of 1.4 V ± 10%. If not suspect the remote interface PWB
or the IBOC/DRM exciter if you are operating in all-digital (HD) mode.
4. Measure the dc voltage at TP1 of the interphase PDM driver PWB. If the voltage is either
0 V (and transmitter not shut back) or 15 V, suspect the control/display PWB.
5. Use an oscilloscope to measure TP2 of the interphase PDM driver PWB. The signal should
be a square wave at the transmitter’s 2f
PDM
frequency (nominal 130 kHz). If not, suspect the
RF synthesizer PWB.
6. Measure the dc voltage at TP3 on the interphase PDM driver PWB. The voltage should be
the B+ voltage multipled by 0.02 ± 10%. If not, suspect the wiring to the B+ distribution
PWB or the exciter interface PWB.
7. If no faults were found in the previous steps, suspect the control/display PWB.
Auto changeover
This event is caused by a fault in the active exciter with the Auto Changeover function enabled. Faults
that cause exciter changeovers are:
Mod Driver Fail A/B
,
RF Driver Fail
and
PDM Drive Fail
.
•
This event triggers the
Changeover
LED to light, and it will remain lit until manually
cleared.
•
No further auto changeovers are possible until the alarm is cleared.
•
The alarm can be cleared remotely by re-selecting the active exciter.
•
The alarm can be cleared locally by use of the Preset screen.
An
Auto Changeover
alarm indicates that the standby exciter is operating and that the transmitter
has switched from main exciter to standby exciter. The
Auto Changeover
alarm may be caused by a
fault in the transmitter that initiated an automatic exciter changeover, or a fault in the control/display
PWB's microprocessor or alarm circuit. Troubleshoot the
Auto Changeover
alarm as follows:
1. Check the
Events Log
to determine the possible cause of the exciter changeover.
2. Troubleshoot any alarms recorded in the
Events Log
to determine the cause of the exciter
changeover.
Содержание XR6
