Nautel NX25 Скачать руководство пользователя страница 70

Страница: 70 / 162

NX300 Operations and Maintenance Manual

Operating the transmitter

Page 2-52

Issue 3.0 2012-11-01

NOTE:

Available settings on the

Analog Settings

and

Digital Settings

tabs are shown/hidden based

on the

Overall Mode

setting. Not all settings are available in all modes.

Analog Settings

(

Figure 2.37 on page 2-54

)

•

AM Source

select the audio source for the AM signal. Options are:

– Balanced Analog (connector J12 on A11A1)

– AES1 (connector J11 on A11A1)

– AES2 (connector J10 on A11A1)

– Audio Player/AES1: Requires installed USB sound card option. Plays audio player playlist through

single-board computer USB port; This USB port must be connected to the USB sound card, the
output of which should be connected to the AES1 input.

– Audio Player/AES2: Same as above for AES2 input.

•

Format

Options are:

– AM Carrier: transmits carrier only; ignores audio inputs.

– Mono L+R: adds L+R channels on AES signal.

– Mono L: transmits L channel of AES signal or Bal Analog.

– Mono R: transmits R channel of AES signal.

– Stereo C-QUAM: uses amplitude and phase modulation over AES, to transmit a stereo AM signal.

•

Filter Type -

selects a filter to be applied to the input audio signal. Options are:

– None: no filter is applied (default).

– Brick Wall: applies a low pass filter with a very sharp cutoff and a 6 dB bandwidth defined by the

Filter Bandwidth setting (between 1 kHz and 10 kHz).

– Minimum Overshoot: applies a Gaussian low pass filter with a very gentle rolloff and a 3 dB

bandwidth of 5.13 kHz. Used to minimize ringing of the modulator filter with extremely high rate of
change input signals (e.g., square waves). Typically used only for testing purposes.

•

Preemphasis -

applies a NRSC-1 pre-emphasis curve to the input audio signal. Default is OFF.

•

Dynamic Carrier Control -

selects the DCC mode, as applicable. Options are None, AMC, EAMC, DAM

or DAM Full. Default is None. When a DCC mode is selectedm a Max DCC Compression level can also
be entered. See

"Selecting the DCC mode", on page 2-57

for more information on each mode.

•

AMSS -

Amplitude Modulation Signalling System. Allows low-bit rate data to be transmitted with the

Analog AM signal. Contact Nautel for assistance with using AMSS. Default is OFF.

Содержание NX25



































































































































































Результаты поиска

Содержание NX25

Отзывы:

Бренды по названию

Популярные бренды

Nautel NX25, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание NX25

Отзывы:

Бренды по названию

Популярные бренды