manualshive.com logo in svg

Nautel NX25, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Nautel NX25 Скачать руководство пользователя страница 118

NX300 Operations and Maintenance Manual

Operating the transmitter

Page 2-100

Issue 3.0  2012-11-01

AM-AM Correction

The 

AM-AM Correction 

page (see 

Figure 2.76

) allows you to load or capture a set of AM-AM 

correction curves.  You can 

Load

 or 

Delete

 curves in this list; you can also capture a curve. When 

you select 

Capture

, the AM-AM Correction window is displayed. Press 

Done

 to capture the curve, 

type a name for the curve, then press 

Save

 (or 

Cancel

). 

Value changes are not typically required. Up to three curves can be saved in memory.

AM-AM curves correct for a type of non-linearity where a change in input amplitude does not cause 
a linearly proportional change in output amplitude. By applying a test signal and monitoring the 
output of the transmitter, the exciter will generate a table of values describing the required gain versus 
input signal level in an attempt to find the inverse curve to the AM-AM non-linearity, and provide a 
more linear amplifier. Applying the proper AM-AM correction will result in lower audio distortion 
and better spectral performace in digital modes of operation.

Figure 2.76: Precorrection AM-AM 

CAUTION: 
Making changes to the AM-AM Correction curves automatically places the 
transmitter in analog AM mode, with full-scale sine-wave modulation. To avoid 
undesirable output or possible antenna damage, it is highly recommended that 
you perform these calibrations while operating the transmitter into a test load.

Содержание NX25



































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды