manualshive.com logo in svg

natus Olympic Warmette 48, Инструкция по эксплуатации, Страница: 45 / 50

Поделиться
Скачать
natus Olympic Warmette 48 Скачать руководство пользователя страница 45

Olympic Warmette Models 48/49 and 55/56 Instruction Manual

8-1

S e c t i o n

8

Specifications

Intended Use

The Warmettes are intended for warming fluids, 
blankets or other linens in a hospital setting.

Dimensions — Model 48/49

Dimensions

„

Height:

84.5 in.

214.6 cm

„

Width:

26.0 in.

66.0 cm

„

Depth:

21.0 in.

53.3 cm

Product Weight

135 lb

61 kg

Shipping Weight 

260 lb

118 kg

Warming Capacity 

13.5 cu. ft.

0.38 cu. m

Dimensions — Model 55/56

Dimensions 

„

Height:

 84.5 in.

214.6 cm

„

Width:

51.8 in.

131.6 cm

„

Depth:

21.0 in.

53.3 cm

Product Weight 

275 lb

125 kg

Shipping Weight 

550 lb

280 kg

Warming Capacity 

27.0 cu. ft.

0.76 cu. m

Electrical

Power Requirements (per module)

„

Voltage: 120–220V~, single phase

„

Consumption: 

„

14.0A (120V~)

„

8.0A (220V~)

„

Frequency (current): 50 ±1

 

Hz or 60 ±1 Hz

Ground

Does not exceed 0.13 

V

Fuses

Two internal 25A 250V FLM time delay fuses

Environmental

Temperature

„

Operating:   50–104°F

 10–40°C

„

Shipping: -40–158°F

-40–70°C

„

Storage:

-40–158°F

-40–70°C

Relative Humidity (RH)

„

Operating: 10–95% relative humidity, non-

condensing

„

Non-operating: 10–100% relative humidity, 

condensing

Operating Altitude

Up to 10000 ft

Up to 3000 m

Pressure

0.5–1.0 atm

500–1060 hPA

Controls

„

Mains power switch changes device state mains 

power on/off ( | / O )

„

SET TEMP 

temperature dial is a thermostat 

control for the internal temperature of the 

Warmette

Содержание Olympic Warmette 48



















































Отзывы:

Нет отзывов