natus Olympic Warmette 48 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 50

natus Olympic Warmette 48 Скачать руководство пользователя страница 19

Olympic Warmette Models 48/49 and 55/56 Instruction Manual

2-5

Testing the Warmette

Testing the Warmette

Test the Warmette after installing it or performing any maintenance or service
procedure to ensure that all systems are functioning properly.

To prepare the Warmette for testing:

1

Plug in the power cord, then press the power switch to the

ON

(|) position.

2

Set the temperature to 120°F.

3

Allow the Warmette to warm up for 5 minutes.

To test the Warmette:

Ensure that the

HEATER ON

lamp is illuminated.

Ensure that the air blowing from the top of the Warmette is noticeably warm.

Listen for the blower to make sure it is running.

Check that the

HEATER ON

lamp turns off within 60 minutes. It will then cycle

on and off to maintain the set temperature.

Electrical Requirements

The Warmette product line has several voltage/frequency options:

120V~, 60 Hz, 14A

220V~, 50 Hz, 8A

220V~, 60 Hz, 8A

CAUTION

This product must be connected directly to a hospital-grade electrical outlet(s) rated for
minimum 20-ampere (A) service. Each heating cabinet is electrically separate. Two
separate electrical outlets are required for the Model 55/56.

«
...
17
18
19
20
21
...
»

Содержание Olympic Warmette 48



















































Отзывы:

Нет отзывов