natus Olympic Warmette 48 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 50

natus Olympic Warmette 48 Скачать руководство пользователя страница 11

Olympic Warmette Models 48/49 and 55/56 Instruction Manual

1-1

S e c t i o n

1

Overview

This section provides an overview of the Olympic Warmette

®

, including the

intended use and a description of the controls and symbols.

About this Manual

This manual provides the necessary information to install, maintain, and service the
Olympic Warmette

®

. The operating instructions in this manual are intended for use

under the direct supervision of a licensed medical practitioner. The installation and
service instructions in this manual are intended for use by qualified service
technicians.

Conventions

Table 1.1 describes the conventions used in this manual.

Table 1.1

Conventions

Convention

Description

NOTE

#

Notes provide additional information to clarify a point in the text.

CAUTION

Cautions indicate situations that, if not avoided, could result in minor
to moderate injury to the patient or operator, or damage to the equipment.

WARNING

Warnings indicate situations that, if not avoided, could result in
serious injury or death to the patient or operator.

BUTTON

This character style represents buttons and controls that the user
can touch or press.

«
...
9
10
11
12
13
...
»

Содержание Olympic Warmette 48



















































Отзывы:

Нет отзывов