background image

Electronic pellet burner controller – NPBC-V3C-K /  NPBC-V4C-K /  NPBC-V4E-K

C

HANGES

 

IN

 

MANUAL

 

FOR

 

THE

 

WORK

 

AND

 

THE

 

SOFTWARE

 

OF

 

THE

 

CONTROLLER

 

 

User

Manual

version

Changes

Pages

3.2

Software version 27/14.

New way of dismissing the alarms for registered problems. Most of 
them are automatically dismissed as soon as the reason for them is no 
longer present. Alarms caused by more serious events require manual 
dismissal by pressing the left navigation button "◄" for more than 2 
seconds.

 

New appearance of the "Information" screen and the "Equipment" menu

1

11
16
17

3.3

Software version 28/14.

Alphabetical order of the languages: Bulgarian, English, Latvian, 
Portugal and Spanish.

Added   option   to   work   with   additional   "Control   module"   with   room
thermostat functions NRC-6 SV

3.4

Software version 31/15.

In case the burner is currently off (due to reached set temperature, for 
instance), but it is about to turn on and if there is a timer scheduled to 
turn it off in 10 minutes or less, the burner will remain off, because 
otherwise the extinguishing procedure may begin before the fire is 
stabilized.

If   OD   input   activates   during   Ignition   or   Unfolding   procedures,   the
extinguishing procedure begins only after switching to any of the power
levels.

 

3.5

Software version 32/16.

If the burner is on and timers are active, holding the On/Off button for 
more than 2 seconds deactivates the timers.

 

Loading first dose time increased to 240 seconds

 

Version screen displays software and hardware version of the controller,
as well as WiFi modem's software version if it is 24

 or higher

18

22

3.6

Software version 34/16.

Main auger’s capacity increased to 350 kg/h.

Consumed pellets graphic's scales increased to 5, 10, 20, 40, 80, 160 
and 320 kg / h 

Minimum value for ignition/extinction level of illumination set to 1

Ignition's level of illumination value must be higher than extinction's.

Added Russian language.

3.7

Software version 46/20

Switch mode choice between Standby, On and Timers

New menu in User settings for fuel selection

User Manual / ver3.8

                                                                        

Page 3 of 33

Содержание NPBC-V3C-K
































Отзывы: