12
13
Activate the autonomous night-light
To activate the autonomous night-light, press
both the Atomisation and Lamp buttons at the
same time until the "1 hour" and "3 hour" indicator
lights blink alternately.
Deactivate the autonomous night-light
To deactivate the function, re-start the operation
until the "3 hour" and "8 hour" indicator lights
blink alternately.
By default, the Taku lamp will turn off at the same time as the mist when the "Timer" function or "Au-
tomatic stop" function is activated. Despite this, you can set up the lamp to work independently of
the aforementioned functions.
Press both buttons simultaneously
Activate the autonomous night-light
Deactivate the autonomous night-light
ADJUSTING THE AUTONOMOUS NIGHT-LIGHT MODE
• When the water reservoir is empty, the atomi-
sation function cannot be activated.
• The temperature of the water, room temperature
and the humidity can affect the quantity of mist
produced and therefore reduce the operational
time.
• Depending on the temperature and quality of
the water, the quantity of mist may initially be
lower.
• The fragrance diffused can vary according to
the ventilation, temperature, humidity and the
size of the room.
• Never empty the water from the side on which the
ventilation hole is located!
IMPORTANT POINTS TO KNOW
MAINTENANCE
• The diffuser has an ultrasound atomiser, which is situated in the middle of
the water reservoir. We advise you to carefully clean the atomiser using
a cotton bud or a damp cloth at least once a week. You can clean the
appliance more often according to its use.
• Never use sharp objects to clean the appliance, at risk of damaging the
atomisation function.
• Remember to unplug the appliance adaptor during cleaning.
• Empty and clean the water reservoir when not in use. If necessary, use
only household detergent to clean the appliance.
ACCIDENTAL LEAK
If the diffuser is tipped over or knocked during use, water may enter into the ventilation hole. There is an
outlet in the base to empty the water from the diffuser. Leakage of water from the base has no incidence
on the operation of the product.
Follow the steps below to avoid water leakage:
• Use the doser to pour in the water.
• Never shake the diffuser when it contains water.
• Avoid frequently moving the diffuser.
REPAIRS
Problem
Possible cause
Solutions
The atomisation function
does not work.
The power supply is not connected.
Plug in the adaptor then press the
atomisation button.
Lack of water.
Fill the water reservoir.
The atomisation function is
not working normally.
Too much water.
Remove the excess water until it falls
below the MAX level.
The ultrasound atomiser is blocked.
Clean the atomiser according to the
instructions in the manual.
The mist indicator is lit up,
the ventilator is working, but
no mist is released.
There is an object or water under the
diffuser preventing air from entering
the hole below the diffuser.
Remove the object under the diffuser
or clean up the water, if any.
Water droplets are blocking the
ventilation hole in the water reservoir.
Remove the blockage from the ven-
tilation hole and clean up the water
covering the hole.
• Model: M2-BA / M2-RO / M2-B / M2-C / M2-R
• Model #: XY12J-2400500Q-XX
• Input Voltage (V): 100V-240 V
• Input AC Frequency (Hz): 50 Hz/60 Hz
• Input Power (W): 12 W
• Output Voltage (V): 24 V
• Output Current (A): 0.5 A
• Output Power (W): 12 W
• Average Active Efficiency (%): 82,96%
• Efficiency at Low Load (10%) (%): 78,43%
• No-Load Power Consumption (W): 0,1 W
• Type of atomisation: ultrasound
• Contents of the reservoir: 180 ml (6.08 fl oz)
• Input: CC 24 V, 12 W
• Dimensions: 127 x 127 x 137 mm (5" x 5" x 5.4")
• Atomisation mode: continuous/intermittent
• Accessories: adaptor, manual
• Made in China
Spare parts are available in case of failure or breakage.
Contact your retailer or the Nature & Découvertes website to check the list.
TECHNICAL SPECIFICATIONS
HOW TO REPAIR YOUR DIFFUSER
Water outlet
Ventilation
outlet
