National Semiconductor LM628 Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 24

background image

LM628 Programming Guide

Introduction

The LM628/LM629 are dedicated motion control processors.
Both devices control DC and brushless DC servo motors, as
well as, other servomechanisms that provide a quadrature
incremental feedback signal. Block diagrams of typical
LM628/LM629-based motor control systems are shown in

Figures 1, 2

As indicated in the figures, the LM628/LM629 are bus pe-
ripherals; both devices must be programmed by a host pro-
cessor. This application note is intended to present a con-
crete starting point for programmers of these precision
motion controllers. It focuses on the development of short
programs that test overall system functionality and lay the
groundwork for more complex programs. It also presents a
method for tuning the loop-compensation PID filter. (Note 1)

Reference System

is a detailed schematic of a closed-loop motor

control system. All programs presented in this paper were
developed using this system. For application of the pro-
grams in other LM628-based systems, changes in basic
programming structure are not required, but modification of
filter coefficients and trajectory parameters may be required.

I. Program Modules

Breaking programs for the LM628 into sets of functional
blocks simplifies the programming process; each block ex-
ecutes a specific task. This section contains examples of the
principal building blocks (modules) of programs for the
LM628.

Note 1:

For the remainder of this paper, all statements about the LM628 also

apply to the LM629 unless otherwise noted.

01086001

FIGURE 1. LM628-Based Motor Control System

01086002

FIGURE 2. LM629-Based Motor Control System

National Semiconductor
Application Note 693
Steven Hunt
January 1999

LM628

Programming

Guide

AN-693

© 2002 National Semiconductor Corporation

AN010860

www.national.com

1
2
3
...
»

Содержание LM628

























Отзывы:

Нет отзывов

Похожие инструкции для LM628

Бренд: D-Link Страницы: 15

Бренд: Paradyne Страницы: 112

Бренд: Intel Страницы: 108

Бренд: ZALMAN Страницы: 4

Бренд: Renesas Страницы: 941

Бренд: Baicells Страницы: 10

Бренд: Moxa Technologies Страницы: 51

Бренд: SafeHome Страницы: 24

Бренд: Extron electronics Страницы: 19

Бренд: Olivella Modular Страницы: 19

Бренд: PairGain Страницы: 68

Бренд: INFRALAN SECURITY Страницы: 15

Бренд: Korg Страницы: 81

Бренд: Honeywell Страницы: 60

Crystal CS98000 Series

Бренд: Cirrus Logic Страницы: 40

Бренд: StarTech.com Страницы: 13

DEQ-P8000 - DSP - External

Бренд: Pioneer Страницы: 6

Бренд: Pioneer Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды