National Semiconductor ADC08200 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 16

National Semiconductor ADC08200 Скачать руководство пользователя страница 6

Y1

T1

U5

L4

+5V
GND
+5V
-5.2V

J4

POWER CONNECTOR

L2

L3

Q2

Q1

TP6

GND

NATIONAL SEMICONDUCTOR
ADC08200 EVAL BOARD

TP4

DGND

U9

U10

TP7
3VCC

U3

TP3
VRFB

TP1

INPUT

RV2

RV1

TP2

VTFT

U8

U2

U1

NUMEM
JP8

DIV_EN

JP7

TP5

DGND

U7

L1

J3

J3

JP2
MEM

JP1

ADCCLK

JP5
DLY0

JP6
DLY1

J1

TP7

3VCC

J4

POWER

CONNECTOR

RV2

VTFB ADJ

RV1

VTFT ADJ

TP3

VTFB

J3

INPUT BNC

TP2

VTFT

TP7

INPUT

JP8

Detail:

Hard-Wired

Position

JP2, JP7

Detail:

Hard-Wired

Position

JP1

CLK FREQ

SELECT

JP1

Detail:

Default Jumper

Position

Figure 1. Component and Test Point Locations

4.0 Functional Description

4.2 ADC reference circuitry

The ADC08200 Evaluation Board schematic is shown in

Figure 2

.

The provided reference circuitry will provide nominal
reference voltage ranges of 1.3V to 2.5V for VRFT and

0V to 1.3V for VRFB, Providing for nominal input ranges

of 0V to 2.5V peak-to-peak.

4.1 Input (signal conditioning) circuitry

The input signal to be digitized should be applied to BNC
connector J3. This 50 Ohm input is intended to accept a
low-noise  sine  wave  signal  of  1.6V  peak-to-peak
amplitude.  To  accurately  evaluate  the  ADC08200
dynamic  performance,  the  input  test  signal  should  be
passed  through  a  high-quality  bandpass  filter  (60dB
minimum stop-band attenuation) as even the best signal
sources  do  not  provide  a  pure  enough  sine  wave  to
properly evaluate an ADC.

The reference voltages for the ADC08200 can be
monitored at test points TP2 and TP3 and are set with
RV1 and RV2. Signal offset can be provided by adjusting
both of these potentiometers.

4.3 ADC clock circuit

The board is shipped ready to accept an ECL clock
oscillator at a frequency of your choosing and is shipped
without an oscillator in its socket. 200 MHz oscillators are
not readily available, but a suitable 200 MHz oscillator is
available from Pletronics, Inc. as their part number
EC1145ME-200.0MPST.

The  input  to  the  ADC08200  is  a.c.  coupled  through
capacitor  C14.  Resistors  R33A  and  R33B  provide  the
needed  input  bias  to  the  ADC08200.  If  d.c.  coupling  is
desired,  be  sure  that  the  input  signal  remains  within  the
limits set by VRT at TP2 and VRB at TP3.

6

http://www.national.com

«
...
4
5
6
7
8
...
»

Содержание ADC08200

















Отзывы:

Нет отзывов