background image

68OMCE-10/01-350

2

NATIONAL  MOWER  COMPANY

ONE YEAR

LIMITED WARRANTY

For the period of one year from the date of purchase (45 days if the product

is used for rental purposes), National Mower Company will repair or replace free

of charge, for the original purchaser, any part or parts found by inspection to be

defective by our Factory Authorized Service Station or by the Factory at St. Paul,

Minnesota to be defective in material or workmanship or both. All transportation

charges on parts submitted for repair or replacement under this warranty shall be

paid for by the purchaser.

This warranty does not include engines, engine parts or tires which are

covered under separate warranties furnished by their manufacture or supplier.

All service under this warranty will be furnished and performed by our Factory

Authorized Service Stations.

-THERE IS NO OTHER EXPRESS WARRANTY-

IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR
FROM PURCHASE OR 45 DAYS IF THE PRODUCT IS RENTED AND TO
THE EXTENT PERMITTED BY LAW, ANY AND ALL IMPLIED WARRANTIES
ARE EXCLUDED. THE ABOVE REMEDY OF REPAIR AND REPLACEMENT
OF DEFECTIVE PARTS IS THE PURCHASER’S EXCLUSIVE REMEDY FOR
ANY DEFECT, MALFUNCTION OR BREACH OF WARRANTY. LIABILITY
FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES UNDER ANY AND ALL
WARRANTIES IS EXCLUDED TO THE EXTENT PERMITTED BY LAW.

NATIONAL

  

  MOWER  COMPANY

700 Raymond Avenue, St. Paul, Minnesota  55414, U.S.A.

Содержание DL TRIPLEX - CE





































Отзывы: