National Mower DL TRIPLEX - CE Скачать руководство пользователя

Страница: 11 / 36

NATIONAL 68" SR & DL TRIPLEX – CE

WING MOWERS

1. Remove Wing Mower Belts (17, Fig. B) from the steer-

ing column.

2. Unlock Hooks (18, Fig. B) from Wing Mower Assem-

blies (19, Fig. B), lower them carefully to the ground.

Slip wing mower belts over Countershaft Pulleys (20,

Fig. B).

3. Block mower wheels to prevent mower from moving

forward. Pull Wing Mower Assemblies (19, Fig. B)

forward so that they slide on Pull Rods (21, Fig. B) and

compress springs. This will allow enough slack to

enable belts to be installed over Reel Pulleys (22, Fig. B).

ENGINE

MOWER IS SHIPPED WITH DRY ENGINE. DO

NOT START ENGINE UNTIL OIL IS ADDED TO

CRANKCASE. See Engine Manual for additional

information.

DIFFERENTIAL

Grease has been installed in the differential at the

factory. Refer to the Maintenance Section, page 7, for

additional information.

ASSEMBLY INSTRUCTIONS

REAR MOWER

1. Remove two 1/2" x 1-1/2" Hex Head Bolts (1, Fig. B)

and nuts from the shipping position in the Seat Hinge

assembly (2, Fig. B). Position Seat Hinge Assembly

with pivot facing rearward, over the seat mount of the

mower frame and fasten with Bolts (1, Fig. B) and lock

nuts.

2. Pivot Seat Brace (3, Fig. B) from the axle so that the

top end aligns with the tab at the back of the seat

hinge assembly. Fasten with a 5/16" x 1" Hex Head

Bolt, Lock Washer and Hex Nut.

3. Remove the Lifter Tee (4, Fig. B) from the shipping

position in the Pivot Tube (5, Fig. B) and set aside

cotter pin and washer for later use. Insert the rod end

of lifter tee through the slotted hole in the pad on the

rear mower frame and secure with the cotter pin and

washer as shown.

4. Fasten Rear Mower Pull Rod (6, Fig. B) inner leg by

removing Bolts (7, Fig. B) and reinserting it through

pull rod and attaching flanges on tractor axle. Note

that Spacers (8, Fig. B) must be in each pivot point to

allow free movement of the pull rod.

5. Attach Pull Rod (6, Fig. B) to Pivot Tube (9, Fig. B) with

Pin (3, Fig. K on page 17) and Spacers (1, Fig. K).

NOTE: Before completing assembly, it will be neces-

sary to refer to the rear Mower Drive Belt Tension

section and Figure K, page 17 for adjusting belt

tension.

6. Install Rear Mower Belt (10, Fig. B) from Countershaft

Pulley (11, Fig. B) to outer Drive Pulley (12, Fig. B).

Idler Pulley (13, Fig. B) must ride on top of lower belt

to provide proper tension. NOTE: It will be necessary

to raise rear mower to allow enough slack to get belt

over pulleys.

SEAT

1. Fasten Seat (15, Fig. B) to seat mounts by threading

four 5/16" x 1" Hex Bolts (16, Fig. B), through 5/16"

lockwashers, through holes in seat mounts and into

the threaded holes in the bottom of the seat.

Содержание DL TRIPLEX - CE





































Результаты поиска

Содержание DL TRIPLEX - CE

Отзывы:

Похожие инструкции для DL TRIPLEX - CE

Бренды по названию

Популярные бренды

National Mower DL TRIPLEX - CE, Руководство пользователя

Результаты поиска

Содержание DL TRIPLEX - CE

Отзывы:

Похожие инструкции для DL TRIPLEX - CE

Бренды по названию

Популярные бренды