National Instruments Two-Slot Embedded Controller NI PXI-8183 Скачать руководство пользователя | Manualshive

Страница: 19 / 69

background image

Chapter 2

Installation and Configuration

©

National Instruments Corporation

2-7

NI PXI-8183 User Manual

•

Local Bus IDE Adapter

—The NI PXI-8183 controller has

two integrated IDE/ATA channels (Primary and Secondary), each
capable of supporting two ATA devices (Master and Slave). Use this
setting to disable one or more of these integrated channels. You should
modify this setting only if specified in other sections of this manual.
The default is

Both

.

•

Quick Boot Mode

—When you enable this option, certain lengthy

BIOS tests that rarely fail are skipped to shorten controller boot time.
The default is

Enabled

.

•

Summary Screen

—This setting controls the display of the summary

screen shown after BIOS completes its initialization, but before
booting takes place. You can disable this screen in the interest of
shortening controller boot time. The default is

Disabled

.

•

PXE Network Boot

—This setting enables the option for booting from

a network PXE server on the subnet. The default is

Disabled

.

Integrated Peripherals Submenu

Use this submenu to apply nondefault configurations to the front panel
peripherals of an NI PXI-8183 controller. Normally, you do not need to
modify these settings, as the factory default settings provide the most
compatible and optimal configuration possible.

•

Serial Port A & B

—This setting enables or disables COM1 and

COM2. You also can change this setting to

Enabled

and modify

the base address and Interrupt Request Level (IRQ) of a port. The
NI PXI-8183 does not have a COM2, so

Serial Port B

is always

disabled. The default is

Auto

, which places COM1 at 0x3F8 IRQ 4

and COM2 at 0x2F8 IRQ 3.

•

Parallel Port

—Use this setting to enable or disable LPT1. You also

can change this setting to

Enabled

and modify the base address,

IRQ level, and ISA Direct Memory Access (DMA) channel of the
port. The default is

Auto

, which places LPT1 at 0x378, IRQ 7, using

ISA DMA Channel 3 if necessary.

•

Parallel Port Mode

—The PC industry has created several different

modes of operation for this port over the years. Usually, the default
setting works for all applications. However, if a parallel port device
specifically requires a nondefault setting, you can change it here.
The default is

Bidirectional

, for full IEEE 1284 capabilities.

«
...
17
18
19
20
21
...
»

Содержание Two-Slot Embedded Controller NI PXI-8183






































































Отзывы:

Нет отзывов

Похожие инструкции для Two-Slot Embedded Controller NI PXI-8183

Бренд: Ebyte Страницы: 8

Бренд: Garmin Страницы: 2

InterReach Fusion ADCP-77-044

Бренд: TE Connectivity Страницы: 236

HAWA-Frontside 60/B

Бренд: hawa Страницы: 28

Millennium P650

Бренд: Matrox Страницы: 54

Бренд: Dantel Страницы: 62

Бренд: Renesas Страницы: 2

PBE-5AC-300-ISO

Бренд: Ubiquiti Страницы: 28

Бренд: Lanner Страницы: 78

Бренд: Z3 Technology Страницы: 87

HHM Series HHM2245SA1

Бренд: TDK Страницы: 2

Бренд: S&T Страницы: 28

Бренд: ADTRAN Страницы: 20

N-FXE 02B Series

Бренд: Lantronix Страницы: 10

Бренд: MCT Страницы: 12

Бренд: Ciara Страницы: 14

ENHANCED PSD 239 H2R

Бренд: ADTRAN Страницы: 2

CG9103-2RS232-1USB

Бренд: BiPOM Electronics Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды