background image

USER GUIDE

TB-4162

Screw Terminal Block for the PXIe-4162

This document explains how to install and use the TB-4162 terminal block with a PXIe-4162
source measure unit (SMU) and includes TB-4162 specifications.

The TB-4162 terminal block is used for screw terminal connections with the PXIe-4162 SMU.

Read this document and the documents listed in the additional resources section about
installation, configuration, and operation of this equipment before you install, configure,
operate, or maintain this product. Users are required to familiarize themselves with installation
and wiring instructions in addition to requirements of all applicable codes, laws, and standards.

Caution

 

Observe all instructions and cautions in the user documentation. Using

the model in a manner not specified can damage the model and compromise the
built-in safety protection. Return damaged models to NI for repair.

Attention

 

Suivez toutes les instructions et respectez toutes les mises en garde de la

documentation utilisateur. L'utilisation d'un modèle de toute autre façon que celle
spécifiée risque de l'endommager et de compromettre la protection de sécurité
intégrée. Renvoyez les modèles endommagés à NI pour réparation.

Notice

 

This device is intended for use only with the PXIe-4162 SMU. For more

information about the PXIe-4162, refer to 

ni.com/manuals

.

Contents

Icons.......................................................................................................................................... 2
Getting Started with the TB-4162.............................................................................................2

Kit Contents and Other Equipment...................................................................................2
Installing the TB-4162...................................................................................................... 2

TB-4162 Specifications.............................................................................................................8

Definitions.........................................................................................................................8
Screw Terminal Wiring..................................................................................................... 9
Physical............................................................................................................................. 9
Environmental Guidelines.................................................................................................9

Compliance and Standards......................................................................................................10

Environmental Management........................................................................................... 10
CE Compliance .............................................................................................................. 10
Export Compliance......................................................................................................... 10
Product Certifications and Declarations..........................................................................11

Содержание TB-4162













Отзывы: