National Instruments PXIe-6591R Скачать руководство пользователя страница 45

Страница: 45 / 98

5-9

NI High-Speed Serial Instruments User Manual

aResetSl

Async

This signal is not required.

This signal is an asynchronous
reset signal from the LabVIEW
FPGA environment. If you create
an input signal to your CLIP and
assign it as

Reset

in the CLIP

wizard, that signal is driven as an
asynchronous reset signal. Reset
all CLIP state machines and logic
whenever this signal is logic
high.

This signal is driven high when
you call the LabVIEW FPGA

Reset

invoke method. Call

Run

on the FPGA VI to deassert this
signal.

Do not use CLIP inputs from the
LabVIEW FPGA VI in the CLIP
until

aResetSl

is deasserted.

Port<0..3>_RX_p

In (pad)

N/A

Dedicated MGT receive signals
for Port <0..3>.

Port<0..3>_RX_n

In (pad)

N/A

Port<0..3>_TX_p

Out (pad)

N/A

Dedicated MGT transmit signals
for Port <0..3>.

Port<0..3>_TX_n

Out (pad)

N/A

Port<0..3>_Mod_
ABS

Async

This signal is asserted when the
module for Port <0..3> is absent.

This signal is also called
MODDEF0.

This signal is grounded when a
module is connected to indicate
that the module is present.

This signal is pulled asserted
when no module is present.

Table 5-4.

PXIe-6592R CLIP Signals (Continued)

Port

Direction

Clock

Domain

Description

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание PXIe-6591R



































































































Результаты поиска

Содержание PXIe-6591R

Отзывы:

Бренды по названию

Популярные бренды

National Instruments PXIe-6591R, Руководство пользователя

Результаты поиска

Содержание PXIe-6591R

Отзывы:

Бренды по названию

Популярные бренды