National Instruments PXIe-5611 Скачать руководство пользователя

Страница: 1 / 28

CALIBRATION PROCEDURE

NI PXIe-5611

This document describes processes to calibrate the NI PXIe-5611 I/Q
modulator. This document provides performance tests to verify if the
instrument is performing within the published specifications. For more
information about calibration, visit

ni.com/calibration

Contents

Initial Setup...................................................................................... 8
Verification ...................................................................................... 11

Verifying LO Filter Response .................................................. 11
Verifying LO Path Gain ........................................................... 12
Verifying Modulation Impairments.......................................... 13
Verifying Modulation Bandwidth and Impairments ................ 15
Verifying RF Path Gain ............................................................ 17

Adjustment....................................................................................... 21

Adjusting LO Filter Response .................................................. 21
Adjusting LO Path Gain ........................................................... 22
Adjusting Modulation Impairments.......................................... 23
Adjusting RF Path Gain............................................................ 24

Appendix A: Calibration Utilities ........................................................... 27

Calibration VI References ............................................................... 27

Where to Go for Support......................................................................... 28

Содержание PXIe-5611





























Результаты поиска

Содержание PXIe-5611

Отзывы:

Похожие инструкции для PXIe-5611

Бренды по названию

Популярные бренды

National Instruments PXIe-5611, Процедура калибровки

Результаты поиска

Содержание PXIe-5611

Отзывы:

Похожие инструкции для PXIe-5611

Бренды по названию

Популярные бренды