National Instruments PXIe-5611 Скачать руководство пользователя

Страница: 11 / 28

National Instruments Corporation

NI PXIe-5611 Calibration Procedure

Note

This array is later used to compensate measurements and correct for splitter loss.

If you do not find the exact frequency needed in the splitter correction array, use the loss
corresponding to the next closest frequency.

You have successfully characterized your splitter.

Verification

This section describes the steps you must follow to verify successful
adjustment of the NI 5611.

Verification tests the following NI 5611 specifications:

•

LO filter response

•

LO path gain

•

Modulation impairments

•

Modulation bandwidth and impairments

•

RF path gain

•

Intermodulation products

Verification of the NI 5611 is complete only after you have successfully
completed all tests in this section.

Verifying LO Filter Response

Complete the following steps to verify the LO filter response of an NI 5611
module using a spectrum analyzer.

Connect the NI 5611 LO OUT front panel connector to the spectrum
analyzer RF INPUT front panel connector.

Connect the PXI Express chassis 10 MHz REF IN rear panel connector
to the spectrum analyzer REF OUT rear panel connector.

Generate a signal with the following NI-RFSG property settings:

•

Frequency (Hz): 85 MHz

•

Power Level (dBm): 0 dBm

•

Generation Mode: CW

•

LO OUT Enabled: Enabled

Use the spectrum analyzer to measure the mean fundamental tone
power using the following spectrum analyzer parameter settings:

•

Center Frequency: Frequency from step 3

•

Reference level: +5 dBm

•

Frequency span: 0 Hz

Содержание PXIe-5611





























Результаты поиска

Содержание PXIe-5611

Отзывы:

Похожие инструкции для PXIe-5611

Бренды по названию

Популярные бренды

National Instruments PXIe-5611, Процедура калибровки

Результаты поиска

Содержание PXIe-5611

Отзывы:

Похожие инструкции для PXIe-5611

Бренды по названию

Популярные бренды