manualshive.com logo in svg

National Instruments PXIe-5611, Процедура калибровки, Страница: 15 / 28

Поделиться
Скачать
National Instruments PXIe-5611 Скачать руководство пользователя страница 15

©

 National Instruments Corporation

15

NI PXIe-5611 Calibration Procedure

If the results are within the selected test limit, the device has passed this 
portion of the verification.

Verifying Modulation Bandwidth and Impairments

Complete the following steps to verify the modulation bandwidth 
performance and modulation impairments of the NI 5611 using a spectrum 
analyzer.

1.

Connect the NI 5611 RF OUT front panel connector to the spectrum 
analyzer RF INPUT front panel connector.

2.

Connect the PXI Express chassis 10 MHz REF IN rear panel connector 
to the spectrum analyzer 10 MHz REF OUT rear panel connector on 
the spectrum analyzer.

3.

Generate an I/Q tone at –50 MHz offset from the carrier with the 
following NI-RFSG property settings:

•

Frequency (Hz): 200 MHz

•

Power Level (dBm): 0 dBm

•

Generation Mode: Arb Waveform

•

Reference Clock Source: ClkIn

4.

Use the spectrum analyzer to measure the mean output power of the RF 
output using the following spectrum analyzer parameter settings:

•

Center frequency: frequency in step 3 + offset in step 3

•

Reference level: +5 dBm

•

Frequency  span:  0  Hz

•

Resolution bandwidth: 500 Hz

•

Sweep time: 5 ms

•

Reference clock source: External

5.

Use the spectrum analyzer to measure the mean output power of image 
using the following spectrum analyzer parameter settings:

•

Center frequency: frequency in step 3 – offset in step 3

•

Reference level: +5 dBm

•

Frequency  span:  0  Hz

•

Resolution bandwidth: 500 Hz

2,500 to

 

5,500

–46

–44

5,500 to

 

6,600

–43

–41

Table 5.  

Modulation Impairments Verification Upper Test Limits 

LO Frequency 

(MHz)

ISR (dBc)

Test Limit

CSR (dBc) 

Test Limit

Содержание PXIe-5611





























Отзывы:

Нет отзывов