National Instruments PXIe-4353 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 20

National Instruments PXIe-4353 Скачать руководство пользователя страница 6

NI PXIe-4353 and TB-4353 Terminal Block Installation Guide

6

ni.com

5.

Insert the stripped end of the signal wires fully into the appropriate terminal. Refer to the label next
to each screw terminal to determine the function of the terminal. The

NI PXIe-4353 User Manual

provides more detailed wiring information. Make sure no exposed wire extends past the screw
terminal. Exposed wire increases the risk of a short circuit that can cause circuit failure.

Figure 4.

TB-4353 Circuit Board Parts Locator Diagram

6.

Tighten the terminal screws to a torque of 0.3 N



·



m (2.7 lb · in.).

Note

In most applications, connection to the COM terminal is not necessary. However, its proper

connection will improve common-mode rejection performance when two or more channels are
connected to different common-mode voltages. In this case, connect COM to earth ground or a fixed
reference voltage, depending on your isolation requirements. All thermocouple channels with respect
to COM on the NI PXIe-4353

must

remain within ±10 V. Refer to the

NI PXIe-4353 User Manual

for more information about proper connection of the COM terminal.

Caution

Any wires connected to the ground must be sufficiently insulated from high voltage.

7.

Attach cable shields to the ground lugs to connect them to chassis ground.

Note

Refer to the

NI PXIe-4353 User Manual

for details about shielding the signals.

8.

Reinstall the strain-relief bar and tighten the strain-relief screws.

9.

Use tie wraps to connect the signal wires to the tie-wrap holes for additional strain relief when
necessary.

10. Reinstall the top cover and tighten the captive top cover screws.

1

Thermistors

2

Screw Terminals

COM

TC0

TC1

TC2

TC

3

TC4

TC5

TC6

TC7

TC

8

T

C

9

TC10

TC11

TC12

TC1

3

TC14

TC15

TC1

8

TC17

TC16

TC19

TC20

TC21

TC22

TC2

3

TC26

TC25

TC24

TC27

TC2

8

TC29

TC

3

0T

C

3

1

+ – + – + – + – + – + – + – + –

+ – + – + – + – + – + – + – + –

+ – + – + – + – + – + – + – + –

+ – + – + – + – + – + – + – + –

1

1

1

1

1

1

1

1

2

2

2

2

2

«
...
4
5
6
7
8
...
»

Содержание PXIe-4353





















Отзывы:

Нет отзывов