National Instruments PXIe-4353 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 20

National Instruments PXIe-4353 Скачать руководство пользователя страница 4

NI PXIe-4353 and TB-4353 Terminal Block Installation Guide

4

ni.com

Figure 1.

Symbols for PXI Express/ PXI Express Hybrid/ PXI Slots

3.

Remove the filler panel and touch any metal part of the chassis to discharge static electricity.

4.

Place the module edges into the module guides at the top and bottom of the slot.

Caution

When installing the module, make sure both edges are positioned inside the guides and that

the module components do not come into contact with adjacent modules.

5.

Slide the module along the guides until it reaches the rear connector, then seat the module by
pushing the front panel until it is flush with the front panel of the chassis.

6.

Secure the module to the chassis using the front-panel captive screws, shown in Figure 2. Tighten
the screws to 0.31 N



·



m (2.7 lb · in.).

Figure 2.

Installing NI SC Express Modules

1

PXI Express System Controller Slot

2

PXI Peripheral Slot

3

PXI Express Hybrid Peripheral Slot

4

PXI Express System Timing Slot

1

Captive Screws

NI PXIe-1062Q

1

2

3

4

NI PXIe-1062Q

COOLING CLEARANCE AND F

AN FIL

TER MAINTENANCE REQ

UIRED

.

S

EE MANU

AL.

CO

OLI

NG

CLEA

RANCE

AND

FA

N F

ILTE

R M

AINT

ENA

NC

E REQ

UIR

ED

.

S

EE

M

ANU

AL

.

1

«
...
2
3
4
5
6
...
»

Содержание PXIe-4353





















Отзывы:

Нет отзывов