National Instruments PXIe-4353 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 20

National Instruments PXIe-4353 Скачать руководство пользователя страница 12

NI PXIe-4353 and TB-4353 Terminal Block Installation Guide

12

ni.com

Figure 8.

Removing the TB-4353 from the NI PXIe-4353 Module (Tilt-Down Method)

3.

Store the terminal block in an antistatic protective bag.

Step 2. Remove the Module

Caution

Do

not

remove a module with the power on. Doing so can damage the module.

1.

Make sure that the chassis is powered off before removing the module.

2.

Loosen the captive screws on the top and bottom of the module.

Caution

Do

not

pull the front panel to remove the module. Doing so may cause module components

to come into contact with adjacent modules, causing damage to the modules.

3.

Pull the captive screws to unseat the module and slowly slide the module along the guides, as shown
in Figure 9.

4.

Replace the filler panel in the empty slot.

5.

Store the module in an antistatic protective bag.

1

PXIe Controller

2

PXIe Chassis

3

TB-4353 Terminal Block

4

Mounting Screw

NI PXIe-1062Q

COOLING CLEARANCE AND F

AN FIL

TER MAINTENANCE REQ

UIRED

.

S

EE MANU

AL.

COOL

ING C

LEA

RA

NCE

AN

D F

AN F

ILTE

R M

AINT

ENA

NCE

RE

QUIRE

D.

S

EE M

ANU

AL.

4

3

2

1

«
...
10
11
12
13
14
...
»

Содержание PXIe-4353





















Отзывы:

Нет отзывов