background image

6

|

ni.com

|

NI PXIe-4340 Calibration Procedure

Allow a warm-up time of at least 15 minutes to ensure that the PXIe-4340 measurement 
circuitry is at a stable operating temperature.

Ensure that the PXI/PXI Express chassis fan speed is set to HIGH, that the fan filters are 
clean, and that the empty slots contain filler panels. For more information, refer to the 

Maintain Forced-Air Cooling Note to Users

 document available at 

ni.com/manuals

.

Initial Setup

Refer to the 

NI PXIe-4340 and TB-4340 Installation Guide and Terminal Block Specifications

 

for information about how to install the software and hardware and how to configure the device 
in NI Measurement & Automation Explorer (MAX).

Note

When a device is configured in MAX, it is assigned a device identifier. Each 

function call uses this identifier to determine which DAQ device to verify. This 
document uses 

Dev1

 to refer to the device name. In the following procedures, use the 

device name as it appears in MAX.

Accuracy Verification

The following performance verification procedures describe the sequence of operations and 
provides the test points required to verify the PXIe-4340. The verification procedures assume 
that adequate traceable uncertainties are available for the calibration references.

The PXIe-4340 has four independent analog input channels. You can verify the accuracy of any 
or all of the channels depending upon your desired test coverage.

Excitation Accuracy

To connect the TB-4340 for excitation verification, install the PXIe-4340 and the TB-4340 in 
the PXI Express chassis according to the instructions in the 

NI PXIe-4340 and TB-4340 User 

Guide and Terminal Block Specifications

. Do not use the excitation verification terminals as 

they are only used for gross field checks and will introduce additional errors.

Complete the following steps to verify the excitation accuracy of the PXIe-4340:
1.

Connect the PXI-4070 across the EX+ and EX- terminals of the channel to be verified.

2.

Refer to Table 3 to configure the PXI-4070 and acquire a voltage measurement for DC 
Offset.

Содержание PXIe-4340











Отзывы: