background image

NI PXIe-1086 Getting Started Guide

|

© National Instruments

|

11

Cleaning

Cleaning procedures consist of exterior and interior cleaning of the chassis. Refer to your 
module user documentation for information on cleaning the individual CompactPCI or 
PXI Express modules.

Caution

Always

 disconnect all power cables before cleaning or servicing the 

chassis.

Interior Cleaning

Use a dry, low-velocity stream of air to clean the interior of the chassis. Use a soft-bristle brush 
for cleaning around components.

Exterior Cleaning

Clean the exterior surfaces of the chassis with a dry lint-free cloth or a soft-bristle brush. If any 
dirt remains, wipe with a cloth moistened in a mild soap solution. Remove any soap residue by 
wiping with a cloth moistened with clear water. Do not use abrasive compounds on any part of 
the chassis.

Caution

Avoid getting moisture inside the chassis during exterior cleaning, 

especially through the top vents. Use just enough moisture to dampen the cloth.

Caution

Do 

not

 wash the front- or rear-panel connectors or switches. Cover these 

components while cleaning the chassis.

Caution

Do 

not

 use harsh chemical cleaning agents; they may damage the chassis. 

Avoid chemicals that contain benzene, toluene, xylene, acetone, or similar solvents.

Replacing a Modular Power Supply

This section describes how to remove and install a modular power supply for the NI PXIe-1086 
chassis.

Caution

Do not use a power supply from another chassis. Doing so may damage 

your chassis and the power supply.

Removal

The NI PXIe-1086 power supply (part number 782106-01) is a replacement part for the 
NI PXIe-1086 chassis. Before attempting to replace a power supply, verify that there is adequate 
clearance behind the chassis.

The power supplies for this chassis are redundant and hot swappable. If both power supplies are 
installed and functional, you can remove either without disconnecting main AC power from the 
system. If both power supplies are installed, and one has failed, you can remove the failed supply 
without disconnecting main AC power from the system.

Содержание PXIe-1086

















Отзывы: