National Instruments PXI-8110 Скачать руководство пользователя | Manualshive

Страница: 32 / 85

background image

Chapter 2

Installation and Configuration

©

National Instruments Corporation

2-17

NI PXI-8110 User Manual

LabVIEW RT Installation

This section explains software installation and switch configuration for
LabVIEW RT on your PXI controller.

LabVIEW RT Software Installation

The following section describes the necessary steps to get your PXI
embedded controller setup to run LabVIEW Real-Time. In this section you
will configure the boot mode of the controller, verify or change IP settings,
and install LabVIEW Real-Time software.

Complete the following steps to install the LabVIEW RT software.

1.

Boot the NI PXI embedded controller into the real-time operating
system. Refer to the

LabVIEW RT Configuration Switches

section

or the

LabVIEW RT Options Setup Menu

section in this manual to

configure the controller for booting into LabVIEW RT.

The PXI controller will automatically boot into LabVIEW RT Safe
Mode when no software is installed. LabVIEW RT Safe Mode loads
with the basic real-time operating system and will automatically
attempt to connect to the network using DHCP. If DHCP is not
available, it will then connect to the network with a link-local
IP address.

Tip

You can connect a monitor to the desktop PC to display startup messages such as the

IP address and MAC address.

2.

Open Measurement & Automation Explorer (MAX) on another
computer in the same subnet and expand the

Remote Systems

branch.

MAX lists the PXI controller as the model name of the controller
followed by the MAC address (for example,
NI-PXI-8110 00802f108562).

Tip

Record the PXI controller MAC address, located on the side of the controller, for use

in identifying the controller. The label also can be removed and placed on the front of the
controller for easier access.

3.

Click on the appropriate PXI controller entry to access the

Network

Settings

tab in the right pane view.

4.

(Optional) Enter a name for the RT target in the

Name

text box.

«
...
30
31
32
33
34
...
»

Содержание PXI-8110






















































































Отзывы:

Нет отзывов

Похожие инструкции для PXI-8110

H3C S7500E Series

Бренд: H3C Страницы: 34

SR8800 IM-FW-II

Бренд: H3C Страницы: 5

H3C S7500E Series

Бренд: H3C Страницы: 50

Бренд: Rolls Страницы: 1

500 - DATASHEET REV 003

Бренд: Intel Страницы: 67

Бренд: B&B Electronics Страницы: 17

High-Precision AD/DA Board

Бренд: Waveshare Страницы: 8

Бренд: ETAS Страницы: 29

Бренд: Digital Audio Corporation Страницы: 164

Бренд: Cypress Semiconductor Страницы: 38

Бренд: NEC Страницы: 47

H8S/2615 Series

Бренд: Renesas Страницы: 28

Бренд: Radio Shack Страницы: 154

Бренд: Hakki Pilke Страницы: 48

Бренд: Actisense Страницы: 14

Бренд: Asus Страницы: 56

MS-9A95 WindBOX IV Advanced

Бренд: MSI Страницы: 51

Бренд: Crestron Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды