National Instruments PCI-6238 Скачать руководство пользователя страница 26

Страница: 26 / 173

Chapter 3

Connector Information

NI 6238/6239 User Manual

3-2

ni.com

AO GND

—

Analog Output Ground

—AO GND is the reference for

AO <0..1>. AI GND and AO GND are connected on the
device.

Note:

AI GND and AO GND are isolated from earth ground,

chassis ground, P0.GND, and P1.GND.

PFI <0..5>/P0.<0..5>

P0.GND

Input

Programmable Function Interface or Static Digital Input
Channels 0 to 5

—Each of these terminals can be individually

configured as an input directional PFI terminal or a digital
input terminal.

As an input, each input PFI terminal can be used to supply an
external source for AI or AO timing signals or counter/timer
inputs.

Note:

PFI <0..5>/P0.<0..5> are isolated from earth ground,

chassis ground, AI GND, AO GND, and P1.GND.

PFI <6..9>/P1.<0..3>

P1.GND

Output

Programmable Function Interface or Static Digital
Output Channels 6 to 9

—Each of these terminals can be

individually configured as an output directional PFI terminal
or a digital output terminal.

As a PFI output, you can route many different internal AI or
AO timing signals to each PFI terminal. You also can route the
counter/timer outputs to each PFI terminal.

Note:

PFI <6..9>/P1.<0..3> are isolated from earth ground,

chassis ground, AI GND, AO GND, and P0.GND.

—

No connect

—Do not connect signals to these terminals.

P0.GND

—

Digital Ground

—P0.GND supplies the reference for input

PFI <0..5>/P0.<0..5>.

Note:

P0.GND is isolated from earth ground, chassis ground,

AI GND, AO GND, and P1.GND.

P1.GND

—

Digital Ground

—P1.GND supplies the reference for output

PFI <6..9>/P1.<0..3>.

Note:

P1.GND is isolated from earth ground, chassis ground,

AI GND, AO GND, and P0.GND.

P1.VCC

—

Digital Output Power

—P1.VCC supplies the power for

digital output lines. The actual power consumed depends on
the load connected between the digital output and P1.GND.

AO POWER SUPPLY

—

Analog Output Power Supply

—AO POWER SUPPLY

supplies power to the analog current output terminals.

Table 3-1.

I/O Connector Signals (Continued)

Signal Name

Reference

Direction

Description

Содержание PCI-6238














































































































































































Результаты поиска

Содержание PCI-6238

Отзывы:

Похожие инструкции для PCI-6238

Бренды по названию

Популярные бренды

National Instruments PCI-6238, Руководство пользователя

Результаты поиска

Содержание PCI-6238

Отзывы:

Похожие инструкции для PCI-6238

Бренды по названию

Популярные бренды