National Instruments NI PXIe-5601 Скачать руководство пользователя страница 8

Страница: 8 / 45

ni.com

NI PXIe-5601 Calibration Procedure

RF Input Calibration (with Attenuator)

The absolute gain accuracy verification procedure uses the results of this procedure.
1.

Connect the power splitter input to the RF source output through the 3.5 mm-to-3.5 mm
cable.

Connect power sensor A to the previously designated reference output of the power splitter.

Connect power sensor B to the other output of the power splitter through the 30 dB
attenuator. Figure 2 shows the completed equipment setup.

Figure 2.

RF Input Calibration (with Attenuator) Equipment Setup

Measure the channel A and channel B power, using the appropriate frequency for the power
sensors, for all frequencies between 10 MHz and 7 GHz with the RF source power set to
0 dBm.

Note

Use the log-like frequency progression: 10, 20, 30, ..., 100, 200, 300, ...,

1,000 MHz, and so on.

Calculate the

RF Input Attenuated Calibration Factor

(dB) for each frequency using the

following equation:

RF Input Attenuated Calibration Factor

Channel B Power

Channel A Power

RF Source

Power Splitter

Power Sensor A

Power Meter

Power Meter Channel A

Power Meter Channel B

Power Sensor B

30 dB Attenuator

Содержание NI PXIe-5601














































Результаты поиска

Содержание NI PXIe-5601

Отзывы:

Бренды по названию

Популярные бренды

National Instruments NI PXIe-5601, Процедура калибровки

Результаты поиска

Содержание NI PXIe-5601

Отзывы:

Бренды по названию

Популярные бренды