National Instruments NI-Motion Скачать руководство пользователя

Страница: 201 / 305

Chapter 13

Torque Control

National Instruments Corporation

13-11

NI-Motion User Manual

C/C++ Code

The following example code is not necessarily complete, and may
not compile if copied exactly. Refer to the

examples

folder on the

NI-Motion CD for files that are complete and compile as is.

Main Function

void main(void)

{

boardID;//

Board identification number

axis;//

Axis number

u16

csr = 0;//

Communication status register

u16

axisStatus;//

Axis status

i32

constant;//

Constant force

i16

adcValue;//

ADC value read

Variables for modal error handling

u16

commandID;//

The commandID of the function

u16

resourceID;//

The resource ID

i32

errorCode;//

Error code

///////////////////////////////

Set the board ID

boardID = 1;

Set the axis number

axis = NIMC_AXIS1;

constant force needed to be maintained

corresponds to 5V for a +/- 5V ADC settings

constant = 2047;

////////////////////////////////

//-------------------------------------------------

Is is assumed that the axis being moved has an

encoder mapped

as //

its primary feedback

//-------------------------------------------------

Set the velocity for the move (in counts/sec)

err =

flex_load_velocity

(boardID, axis, 10000,

0xFF);

CheckError;

Set the acceleration for the move (in

counts/sec^2)

err =

flex_load_acceleration

(boardID, axis,

NIMC_ACCELERATION, 100000, 0xFF);

CheckError;

Set the deceleration for the move (in

counts/sec^2)

Содержание NI-Motion


















































































































































































































































































































Результаты поиска

Содержание NI-Motion

Отзывы:

Похожие инструкции для NI-Motion

Бренды по названию

Популярные бренды

National Instruments NI-Motion, Руководство пользователя

Результаты поиска

Содержание NI-Motion

Отзывы:

Похожие инструкции для NI-Motion

Бренды по названию

Популярные бренды