National Instruments NI 9225 Скачать руководство пользователя страница 31

Страница: 31 / 32

NI 9225 Operating Instructions and Specifications

product safety. You can obtain the DoC for your product by visiting

ni.com/certification

. If your product supports calibration,

you can obtain the calibration certificate for your product
at

ni.com/calibration

National Instruments corporate headquarters is located at
11500 North Mopac Expressway, Austin, Texas, 78759-3504.
National Instruments also has offices located around the world. For

telephone support in the United States, create your service request
at

ni.com/

upport

or dial 1 866 ASK MYNI (275 6964). For

telephone support outside the United States, visit the Worldwide

Offices section of

ni.com/niglobal

to access the branch office

websites, which provide up-to-date contact information, support
phone numbers, email addresses, and current events.

Содержание NI 9225

































Результаты поиска

Содержание NI 9225

Отзывы:

Бренды по названию

Популярные бренды

National Instruments NI 9225, Инструкция по эксплуатации и технические характеристики

Результаты поиска

Содержание NI 9225

Отзывы:

Бренды по названию

Популярные бренды