National Instruments NI 9225 Скачать руководство пользователя страница 3

Страница: 3 / 32

NI 9225 Operating Instructions and Specifications

Safety Guidelines

Operate the NI 9225 only as described in these operating
instructions.

Hot Surface

This icon denotes that the component may

be hot. Touching this component may result in bodily
injury.

Hazardous Voltage

This icon denotes a warning

advising you to take precautions to avoid electrical
shock.

Caution

Do not operate the NI 9242 in a manner not

specified in this manual. Product misuse can result in a
hazard. You can compromise the safety protection built

into the product if the product is damaged in any way. If
the product is damaged, return it to National Instruments
for repair.

Safety Guidelines for Hazardous Voltages

If hazardous voltages are connected to the module, take the
following precautions. A hazardous voltage is a voltage greater

than 42.4 V

or 60 VDC to earth ground.

Содержание NI 9225

































Результаты поиска

Содержание NI 9225

Отзывы:

Бренды по названию

Популярные бренды

National Instruments NI 9225, Инструкция по эксплуатации и технические характеристики

Результаты поиска

Содержание NI 9225

Отзывы:

Бренды по названию

Популярные бренды