National Instruments ISC-1762 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 80

background image

6-4

|

ni.com

Chapter 6

LEDs and DIP Switches

FAIL LED

The FAIL LED is a red LED that is user-configurable through the IMAQ property node in
LabVIEW or the

Read/Write I/O

step in Vision Builder AI.

If the IMG ACQ LED and the FAIL LED both flash red, it indicates that the NI Smart Camera
has shut down because the maximum internal temperature was exceeded. Refer to the

Considerations

section of Chapter 8,

Thermal Considerations and Mounting

, for information

about measuring the temperature of the smart camera. Refer to Appendix A,

Specifications

complete temperature specifications.

Configuring DIP Switches

This section describes the SAFE MODE, IP RESET, NO APP, and CONSOLE DIP switches on
the NI Smart Camera. To turn on a DIP switch, lift the DIP switch cover and move the switch to
the ON position.

Caution

To avoid potential damage to your device, use care when configuring DIP

switches. Do not use blunt tools or excessive force when changing the switch
position.

SAFE MODE Switch

To start the NI Smart Camera in safe mode, move the SAFE MODE switch to the ON position
and reapply power or restart the smart camera. If the switch is in the ON position when the smart
camera starts, the smart camera launches only the essential services required for updating
configuration information and installing software. The LabVIEW Real-Time engine does not
launch. Use safe mode to reconfigure the smart camera TCP/IP settings, update firmware, and
to install or update the software on the smart camera.

If the software on the smart camera is corrupted, start the smart camera in safe mode and update
the software. To resume normal operations, move the SAFE MODE

switch to the OFF

position

and reapply power or restart the smart camera. Refer to

Getting Started with the NI 17xx Smart

Camera

for information about updating the software on the smart camera.

The STATUS LED flashes green three times when the smart camera is in safe mode. Keep the
SAFE MODE switch in the OFF position during normal operation.

S

AFE MODE

IP RE

S

ET

NO APP

CON

S

OLE

ON

«
...
46
47
48
49
50
...
»

Содержание ISC-1762

















































































Отзывы:

Нет отзывов

Похожие инструкции для ISC-1762

Бренд: Samsung Страницы: 98

Бренд: Samsung Страницы: 4

Бренд: Samsung Страницы: 161

Бренд: Samsung Страницы: 14

Бренд: Samsung Страницы: 103

Бренд: Samsung Страницы: 128

S1050 - Digital Camera - Compact

Бренд: Samsung Страницы: 100

Бренд: Samsung Страницы: 8

Бренд: Samsung Страницы: 96

Бренд: Samsung Страницы: 103

Бренд: Samsung Страницы: 104

Бренд: Samsung Страницы: 173

Бренд: Samsung Страницы: 2

SL35 - Digital Camera - Compact

Бренд: Samsung Страницы: 102

Бренд: Samsung Страницы: 98

SL202 - Digital Camera - Compact

Бренд: Samsung Страницы: 22

Бренд: Samsung Страницы: 82

Бренд: Samsung Страницы: 94

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды