National Instruments IMAQ SCB-100 Скачать руководство пользователя страница 13

Страница: 13 / 14

General

Number of screw terminals

101 (includes one no connect); all I/O signals
are available at screw terminals

Cold-junction sensor

Accuracy

.±0.5 °C

Output

.10 mV/°C

Caution

Do not connect hazardous voltages (≥42 V

/60 VDC).

Power Requirement

Power consumption (at +5 VDC ±5%),
typical

10 mA with no signal conditioning installed

Note

Limit the current drawn from the host computer's +5 VDC to about 800 mA,

maximum.

Physical Characteristics

Dimensional drawings are available on the SCB-100 product page.

Box dimensions

17.93 cm × 15.37 cm × 4.50 cm (7.06 in. ×
6.05 in. × 1.77 in.)

Weight

897 g (1 lb 15.6 oz)

I/O connectors

One 100-pin female 0.050 series shielded D-
type connector

Screw terminals

101, including one No Connect (NC)

Wire gauge

14-26 AWG

Environmental

Operating temperature

0 to 70 °C

Storage temperature

-55 to 125 °C

Relative humidity

5 to 90% noncondensing

Maximum altitude

2,000 m

Pollution Degree (indoor use only)

Waste Electrical and Electronic Equipment (WEEE)

EU Customers

This symbol indicates that waste products should be disposed of

separately from municipal household waste according to

NI SCB-100 Installation Guide and Specifications

Содержание IMAQ SCB-100















Результаты поиска

Содержание IMAQ SCB-100

Отзывы:

Похожие инструкции для IMAQ SCB-100

Бренды по названию

Популярные бренды

National Instruments IMAQ SCB-100, Руководство по установке

Результаты поиска

Содержание IMAQ SCB-100

Отзывы:

Похожие инструкции для IMAQ SCB-100

Бренды по названию

Популярные бренды