National Instruments IMAQ SCB-100 Скачать руководство пользователя страница 2

Страница: 2 / 14

Figure 1. SCB-100 Connector Block

1. Quick Reference Label
2. Top Cover
3. 100-Pin Connector Screw
4. Grounding Screw
5. 100-Pin I/O Connector

6. Base
7. Strain-Relief Hardware
8. Strain-Relief Screws
9. SCB-100 Board Assembly

What You Need to Get Started

•

SCB-100 100-pin shielded connector block and quick reference label

•

100-pin DAQ device and device documentation

•

SH100100 cable (part number 182853-0x) for E Series/MIO devices or SH100-100-F
cable (part number 185095-0x) for DIO/TIO Series devices

•

Phillips #1 and #2 screwdrivers

•

14-26 AWG wire

•

Wire cutters

•

Wire insulation strippers

•

1/8 in. flathead screwdriver

•

Soldering iron and solder (optional)

•

Long-nose pliers (optional)

•

Resistors and capacitors specific to your application (optional)

Attaching the Quick Reference Label

A quick reference label is included in the SCB-100 100-pin shielded connector block kit to
show switch configurations and define screw terminal pinouts for E Series devices. Place the
label on the inside of the top cover.

ni.com

NI SCB-100 Installation Guide and Specifications

Содержание IMAQ SCB-100















Результаты поиска

Содержание IMAQ SCB-100

Отзывы:

Похожие инструкции для IMAQ SCB-100

Бренды по названию

Популярные бренды

National Instruments IMAQ SCB-100, Руководство по установке

Результаты поиска

Содержание IMAQ SCB-100

Отзывы:

Похожие инструкции для IMAQ SCB-100

Бренды по названию

Популярные бренды