National Instruments GPIB Series Скачать руководство пользователя | Manualshive

Страница: 22 / 62

background image

Chapter 2

Installation

GPIB-ENET/100 for Windows Me/98/95

2-6

ni.com

The time required for assigning the IP address depends on your network
and the configuration of your GPIB-ENET/100. Allow up to 90 seconds
and observe the state of the

PWR/RDY

LED to determine the outcome of

the self tests. One of the following should occur:

•

A steady yellow

PWR/RDY

LED indicates the GPIB-ENET/100

passed its self tests and acquired its IP address. The unit is now ready
to operate. When using DHCP, the GPIB-ENET/100 typically is ready
to operate about 15 seconds after you power it on. Run the GPIB
Configuration utility as described in Chapter 4,

GPIB Configuration

to add the unit to your GPIB system.

•

If the

PWR/RDY

LED continues to alternate rapidly between red and

yellow, the unit was unable to use DHCP to configure its network
parameters. If your network does not have DHCP, you must use the
NI Ethernet Device Configuration utility, as described in Chapter 3,

Ethernet Configuration

, to give your unit its network configuration.

If this utility is successful, the

PWR/RDY

LED should become steady

yellow. Then you can run the GPIB Configuration utility as described
in Chapter 4,

GPIB Configuration

. Refer to Appendix B,

Troubleshooting and Common Questions

, if the LED does not change

to steady yellow.

•

If the

PWR/RDY

LED is steady red, the GPIB-ENET/100 has an

unrecoverable error. Contact National Instruments Technical Support.

•

If the

PWR/RDY

LED blinks a slow red/yellow pattern, the

GPIB-ENET/100 did not pass its self tests. Refer to Appendix A,

PWR/RDY LED Signaling

, to interpret the flash pattern before calling

National Instruments Technical Support.

You can skip Chapter 3,

Ethernet Configuration

, if your GPIB-ENET/100

can use DHCP, although you do need to use the NI Ethernet Device
Configuration utility if you want to change the hostname from the default
hostname listed on the baseplate label.

Note

If at any time you want to return the GPIB-ENET/100 to its default configuration

state as given on the baseplate label, press and hold the CFG RESET switch for three
seconds while you switch the power on. This switch is located on the rear panel, as shown
in Figure 2-4. Refer to the

Using the CFG RESET Switch

section in Chapter 6,

GPIB-ENET/100 and NI-488.2

, for more information.

«
...
20
21
22
23
24
...
»

Содержание GPIB Series































































Отзывы:

Нет отзывов

Похожие инструкции для GPIB Series

Бренд: ZETR Страницы: 2

Бренд: Salusfin Страницы: 6

Бренд: Kanguru Страницы: 13

Бренд: Renesas Страницы: 4

Through Hole Power Inductors 1411

Бренд: Delta Electronics Страницы: 1

Бренд: Aewin Technologies Страницы: 86

Бренд: XtendLan Страницы: 52

crown PIP Series

Бренд: Harman Страницы: 16

PXI Terminal Block NI TB-2709

Бренд: National Instruments Страницы: 12

Бренд: Sony Ericsson Страницы: 2

Powereta iQP Series

Бренд: TDK Страницы: 2

Acme Packet 3900

Бренд: Oracle Страницы: 70

Бренд: A.E.B. Страницы: 28

Бренд: Uctronics Страницы: 12

Бренд: IBM Страницы: 168

Бренд: Proxim Страницы: 65

Бренд: ZyXEL Communications Страницы: 114

Бренд: Intel Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды