National Instruments GPIB Series Скачать руководство пользователя | Manualshive

Страница: 37 / 62

background image

©

National Instruments Corporation

6-1

GPIB-ENET/100 for Windows Me/98/95

6

Using Your GPIB-ENET/100
and NI-488.2

This chapter describes how to use the following options available with the
GPIB-ENET/100 and NI-488.2 for Windows Me/98/95:

•

NI-488.2 Getting Started Wizard

•

Dynamic Host Configuration Protocol (DHCP)

•

Configuration Reset (CFG RESET) switch

•

Firmware update utility

NI-488.2 Getting Started Wizard

The NI-488.2 Getting Started Wizard helps you get started with GPIB
instrument communication using the Measurement & Automation
Explorer. To run the NI-488.2 Getting Started Wizard, select

Start»Programs»National Instruments

»

NI-488.2

»

Getting Started

.

After the NI-488.2 Getting Started Wizard runs the NI-488.2
Troubleshooting Wizard to verify the installation, click

Communicate

with your instrument

. The Getting Started Wizard then steps you through

communicating with your GPIB instruments via the Measurement &
Automation Explorer.

«
...
35
36
37
38
39
...
»

Содержание GPIB Series































































Отзывы:

Нет отзывов

Похожие инструкции для GPIB Series

Бренд: Barracuda Networks Страницы: 2

Бренд: Parker Страницы: 344

Бренд: FabiaTech Страницы: 4

Бренд: Yamaha Страницы: 6

Бренд: Yamaha Страницы: 4

Бренд: Yamaha Страницы: 22

Бренд: Yamaha Страницы: 49

Бренд: M86 Security Страницы: 46

Бренд: ETAS Страницы: 69

Storage Networking (Unified Fabric Pilot)

Бренд: Qlogic Страницы: 76

Бренд: Kontron Страницы: 62

POD-51EH-C541U-12

Бренд: IceTech Страницы: 8

Бренд: Intel Страницы: 154

Serial Attached SCSI (SAS) Expander Card

Бренд: Adaptec Страницы: 26

Бренд: Xilinx Страницы: 29

Service Aggregation Router 7705

Бренд: Alcatel-Lucent Страницы: 20

Бренд: Commell Страницы: 18

Бренд: NEC Страницы: 47

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды