National Instruments Fieldpoint CFP-2200 Скачать руководство пользователя | Manualshive

Страница: 18 / 38

background image

cFP-2200/2210/2220

18

ni.com

Wiring Power to the cFP-22

xx

The cFP-22

xx

requires an external power supply that meets the

specifications in the

Power Requirements

section. The cFP-22

xx

filters and

regulates the supplied power and provides power for all of the I/O modules.
You must connect a power supply to at least one pair of V and C terminals.
Optionally, you can connect a power supply to the other pair of V and
C terminals. The controller draws power from the power supply with the
higher voltage. The controller has one layer of reverse-voltage protection.

Caution

In order to comply with standards and laws governing electromagnetic emissions

and compatibility, you must install the ferrite shipped with the controller. If you decide to
connect an optional second power supply, you must install a second, similar ferrite. You
can order the ferrite from

ni.com

. The ferrite is NI part number 711849-01.

Complete the following steps to connect power supplies to the controller.

1.

Install the ferrite 2–3 in. from the ends of the power wires. Wrap the
wires around one side of the ferrite so that they pass through the ferrite
twice, as shown in Figure 22.

Figure 22.

Wrapping the Power Wires around the Ferrite

Figure 23.

Closed Ferrite

«
...
16
17
18
19
20
...
»

Содержание Fieldpoint CFP-2200







































Отзывы:

Нет отзывов

Похожие инструкции для Fieldpoint CFP-2200

Бренд: Yudian Страницы: 26

Бренд: National Instruments Страницы: 6

Бренд: National Instruments Страницы: 6

Бренд: IBM Страницы: 20

Бренд: DAV TECH Страницы: 24

Бренд: OBSIDIAN CONTROL SYSTEMS Страницы: 16

Бренд: RKC INSTRUMENT Страницы: 10

Total Access 351 Series

Бренд: ADTRAN Страницы: 4

Бренд: Reer Страницы: 2

Бренд: baby joy Страницы: 11

Бренд: Dickey-John Страницы: 109

by-me Eikon 20526

Бренд: Vimar Страницы: 6

Бренд: SMC Networks Страницы: 15

Бренд: YASKAWA Страницы: 12

Бренд: Contemporary Research Страницы: 22

Бренд: EBS Страницы: 118

IconRemote IR10A

Бренд: X10 Страницы: 21

Бренд: DS Produkte Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды