background image

Figure 3. cRIO-9033 Buttons

1

2

3

4

1. Power Button
2. RESET Button

3. USER1 Button
4. CMOS Reset Button

Power Button

The default behavior for the cRIO-9033 is to power on when you apply power to the controller
and power off when you press and release the power button. The behavior of the power button
can be configured in the BIOS.

If the cRIO-9033 becomes unresponsive, you can power it off by holding the power button for
4 seconds.

Related Information

Power/Wake Configuration Submenu

 on page 36

RESET Button

Press the RESET button to reset the processor in the same manner as cycling power.

Troubleshooting Network Connectivity

You can use the RESET button to troubleshoot network connectivity.

Complete the following steps to reset the network adapters to default settings.
1.

Hold the RESET button for 5 seconds, and then release it to boot the controller in safe
mode and enable Console Out.

2.

Hold the RESET button again for 5 seconds to boot the controller into safe mode, enable
Console Out, and reset network adapters to default settings.

System Reset

The following figure shows the reset behavior of the cRIO-9033.

NI cRIO-9033 User Manual

  | 

© National Instruments

  | 

15

Содержание cRIO-9033









































Отзывы: