National Instruments 6008 Скачать руководство пользователя

Страница: 26 / 27

NI USB-6008/6009 User Guide and Specifications

ni.com

Storage temperature
(IEC 60068-2-1 and IEC 60068-2-2)......–40 to 85 °C

Storage humidity
(IEC 60068-2-56) ..................................5 to 90% RH, noncondensing

Pollution Degree (IEC 60664) ................2

Electromagnetic Compatibility

This product is designed to meet the requirements of the following
standards of EMC for electrical equipment for measurement, control,
and laboratory use:

•

EN 61326 EMC requirements; Minimum Immunity

•

EN 55011 Emissions; Group 1, Class A

•

CE, C-Tick, ICES, and FCC Part 15 Emissions; Class A

Note

The NI USB-6008/6009 may experience temporary variations in analog input

readings when exposed to radiated and conducted RF noise. The device returns to normal
operation after RF exposure is removed.

Note

For EMC compliance, operate this device according to product documentation.

CE Compliance

This product meets the essential requirements of applicable European
Directives, as amended for CE marking, as follows:

•

73/23/EEC; Low-Voltage Directive (safety)

•

89/336/EEC; Electromagnetic Compatibility Directive (EMC)

Note

Refer to the Declaration of Conformity (DoC) for this product for any additional

regulatory compliance information. To obtain the DoC for this product, visit

ni.com/

certification

, search by model number or product line, and click the appropriate link

in the Certification column.

Waste Electrical and Electronic Equipment (WEEE)

EU Customers

At the end of their life cycle, all products

must

be sent to a WEEE recycling

center. For more information about WEEE recycling centers and National Instruments
WEEE initiatives, visit

ni.com/environment/weee.htm

Содержание 6008




























Результаты поиска

Содержание 6008

Отзывы:

Похожие инструкции для 6008

Бренды по названию

Популярные бренды

National Instruments 6008, Руководство пользователя и технические характеристики

Результаты поиска

Содержание 6008

Отзывы:

Похожие инструкции для 6008

Бренды по названию

Популярные бренды