background image

3

2.2 

Organizational Measures

Operating Instructions must be kept near the machine and be reachable at all times.

In addition to the Operating Instructions, general and legal regulations regarding accident 

prevention and environmental protection must be adhered to.
Such duties may, for example, relate to the handling of hazardous substances or to the provision 

and wearing of personal protection equipment, as well as compliance with local traffic regulations.
The Operating Instructions must be supplemented by instructions regarding the duty to supervise 

and report local working practices (e.g. work organization, work procedures, and personnel 

allocation).
Personnel entrusted with working with the machine must have read the Operating Instructions 

before starting the work. This particularly applies to incidental activities such as setting up the 

machine, carrying out maintenance work, or training staff to work with the machine.
The working practices of the staff should be checked regularly, specifically regarding awareness of 

safety and hazards.
Personnel must tie back long hair and not wear loose clothing or jewelry. 
All safety and hazard notices on the machine must be kept complete and legible.
If safety-critical changes occur to the machine or its performance, the machine must be shut down 

immediately! The cause of the fault has to be established immediately and the machine must be 

repaired before starting the work again. 

Changes, add-ons, or conversions of the machine which might have an influence to the 

safety of the machine must not be undertaken without the permission of the manufacturer.

This applies in particular to the fitting and adjustment of safety devices and to welding on major 

and load bearing parts. 
Spare parts must always comply with the technical requirements and specifications of the 

manufacturer. This is always guaranteed with original spare parts from the manufacturer.
Intervals for recurring inspections specified in these Operating Instructions must be complied with.
The location and the operation of fire extinguishers must be made known at each building site. 

Take note of the facilities for fire reporting and fighting fires.

Содержание GP18






















Отзывы: