Narex EV 13 G-2, Оригинальное руководство по эксплуатации, Страница: 15 / 36

English
15
Commissioning and use
Any unauthorised use might cause damage to the tool. Therefore
follow these instructions:
- Always use sharp drill bits.
- Load the tool to avoid any significant reduction of speed or
stoppage.
- Always change the speed gear when the machine is idle or at
the machine slow-down at low speed, in no case during the
drilling or when the machine is otherwise loaded.
Check whether the data on the rating plate match with the real
power supply voltage. The tool intended for 230 V~ may be also
connected to 220/240 V~. Check whether the plug type corre-
sponds to the socket type.
Attention! Prior to handling the accessories, the pow-
er supply cable has always to be disconnected from
the power source socket!
Additional handle SOFTGRIP
For safety reasons always use the additional handle (11), firmly
mounted on the clamping neck (3). The stop bar (12) can be used
to adjust the drilling depth. By rotating the handle the position of
the addition al handle and the depth stop can be modified.
Clamping of drill bits
Chuck with ring gear
Open the chuck to allow mounting of the tool. Mount the tool on.
Mount the tool on and, using the chuck hook (13) clamp in evenly.
Quick-tightening chuck
Open the chuck to allow mounting of the tool. Mount the tool on.
Tighten the quick-tightening chuck by your hand so strongly that
a “click” sound is heard clearly. Thus the chuck will be secured au-
tomatically.
This lock will release again if you turn the sleeve contra direction-
ally to remove the tool.
Be careful as the chuck gets hot:
In case of longer work tasks, especially in impact drill-
ing, the chick might get very hot. In this case you are
recommended to wear protective gloves.
Controls
1 ...........Chuck with ring gear
2 ...........Spots on spindle
3 ...........Clamping neck
5 ...........Air vents
6 ...........Latching pin
7 ...........Switch / controller
8 ...........Speed pre-selection wheel
9 ...........Alteration switch lever
10 .........Gear-shifting lever
11 .........Additional handle
12 .........Stop bar
13 .........Chuck hook
14 .........Spanner
15 .........Socket screw wrench
16 .........Quick-tightening chuck
The displayed or described accessories need not be included in the
delivery package.
Double insulation
To ensure maximum safety of the user, our tools are designed and
built to satisfy applicable European standards (EN standards). Tools
with double insulation are marked by the international symbol of
a double square. These tools must not be grounded and a two-wire
cable is sufficient to supply them with power. Tools are shielded in
accordance with EN 50114.
Use
The machine is intended drilling in wood, metal, ceramic and plas-
tic. Machines with electronic control and right/left rotation are also
suitable for screwing and thread cutting ( Only for soft screwdriv-
ing applications).
The user alone is responsible for any liabilities caused by usage
other than intended.
Technical data
Impact drill
Type EV 13 G-2 EV 13 G-2A
Supply voltage 230–240 V 230–240 V
Power frequency 50–60 Hz 50–60 Hz
Power input 760 W 760 W
Speed under load
1st speed gear 0–600 rpm 0–600 rpm
2nd speed gear 0–1 750 rpm 0–1 750 rpm
Idle speed
1st speed gear 0–1 100 rpm 0–1 100 rpm
2nd speed gear 0–3 050 rpm 0–3 050 rpm
Speed pre-selection
ü ü
Right-left turning ü ü
Extent of chuck dia. 1.5–13 mm 1.5–13 mm
Thread on spindle 1/2“-20 UNF 1/2“-20 UNF
Quick-tightening chuck Auto-Lock
û ü
Drilling dia. max
into steel 13 mm 13 mm
into aluminium 25 mm 25 mm
into wood 45 mm 45 mm
Clamping neck dia. 43 mm 43 mm
Weight 2.0 kg 2.1 kg
Protection class II / II /