![background image](http://html1.mh-extra.com/html/napoleon/rxt425/rxt425_owners-manual_4179664020.webp)
20
| Troubleshooting
Napoleon.com
| Rogue® Series Grills
Tr
ou
bl
es
ho
ot
in
g
Gas Flow
• Low heat or low flame when valve is turned to high.
• Burners burn with yellow flame, accompanied by the smell of gas.
• Flames lift away from burner, accompanied by the smell of gas, and possible lighting difficulties.
• Burner output on HIGH, but setting is LOW. Rumbling noise and fluttering blue flame at burner surface.
Possible causes
Solution
Propane – improper lighting procedure
Ensure lighting procedure is followed carefully. All gas valves must
be in the OFF position when the tank valve is turned on. Turn tank
on slowly to allow pressure to equalize. See Operation –
"Lighting
Instructions".
Natural gas – undersized supply line.
Pipe must be sized according to installation code.
Leaking gasket surrounding the ceramic tile, or a weld
failure in the burner housing.
Allow burner to cool and inspect very closely for cracks. Contact
your authorized Napoleon dealer to order replacement burner
assembly if any cracks are found.
Both gas propane and natural gas – improper preheating.
Preheat grill with both main burners on high for 10 to 15 minutes.
Possible spider web or other debris.
Thoroughly clean nest or webs out of your burner orifice by
removing it and following instructions in this manual.
See
"Leak Test".
Improper air shutter adjustment.
Open or close air shutter slightly according to this manual.
See
"Maintenance Instructions".
IMPORTANT
! This must be done by a qualified gas installer.
Lack of gas
Check gas level in propane cylinder.
Supply hose is pinched.
Reposition supply hose as necessary.
Propane regulator in low flow state.
Turn the burners off and close the tank valve, wait 5 minutes
before fully re-opening the valve, allow a few seconds for the
pressure to equalize before following the Lighting Instructions to
start the grill. Ensure igniting procedure is followed carefully every
time you cook. All gas valves must be OFF when the tank valve is
turned on. Always open the tank valve slowly.
Infrared Burner Flashes Back
• During operation the burner abruptly makes a loud whoosh sound, followed by a continuous blow-torch type sound and
grows dim or has a large flame on start up.
Possible causes
Solution
Ceramic tiles overloaded with grease drippings and build-
up. Ports are clogged
Turner burner OFF and allow to cool for at least 2 minutes.
Reignite burner and burn on HIGH for at least 5 minutes, or until
the ceramic tiles are evenly glowing red.
Burner overheated because inadequate ventilation. Too
much grill surface covered by griddle or pan.
Ensure no more than 75% of the grill surface is covered by
objects or accessories. Turn burner OFF and allow to cool for at
least 2 minutes. Reignite.
Leaking gasket surrounding the ceramic tile, or a weld
failure in the burner housing.
Allow burner to cool and inspect very closely for cracks. Contact
your authorized Napoleon dealer to order replacement burner
assembly if any cracks are found.
Improper heating.
Preheat grill with both main burners on high for 10 to 15 minutes.
Excessive grease and ash build on sear plates and in drip
pan.
Clean sear plates and drip pan regularly. Do not line pan with
aluminum foil. Refer to "
Cleaning Instructions".
Peeling Paint
• Paint appears to be peeling inside lid or hood.
Possible causes
Solution
Grease build-up on inside surfaces.
This is not a defect. The finish on the lid and hood is porcelain
or stainless steel and will not peel. The peeling is caused by
hardened grease, which dries into paint-like shards, that flake off.
Regular cleaning will prevent this. See
"Cleaning instructions".
Содержание RXT425
Страница 22: ...22 Napoleon com Rogue Series Grills...
Страница 67: ...Napoleon com Rogue Series Grills 67 Notes...