background image

27

W415-1034 /  09.01.11

9.0 REPLACEMENTS

COMPONENTS

REF NO.

PART NO

DESCRIPTION

1

W725-0056

NATURAL GAS VALVE

1

W725-0057

PROPANE GAS VALVE

2

W456-0042

#42 NATURAL GAS BURNER ORIFICE

2

W456-0053

#53 PROPANE GAS BURNER ORIFICE (FRONT BURNER)

3

W010-1865

NATURAL GAS PILOT ASSEMBLY

3

W010-1866

PROPANE GAS PILOT ASSEMBLY

4*

W455-0070

NATURAL GAS PILOT INJECTOR

5*

W455-0068

PROPANE GAS PILOT INJECTOR

6*

W385-0334

NAPOLEON LOGO

7*

W562-0008 GLASS 

GASKET

8*

W010-2701

GLASS W/ GASKET

9

W010-2702

DOOR, GLASS & GASKET ASSEMBLY

10

W010-2705

BURNER TUBE ASSEMBLY

11*

W190-0029

IPI BOARD

12*

W707-0010

NIGHT LIGHT TRANSFORMER

13*

W290-0080

NIGHT LIGHT GASKET

21*

W387-0006

NIGHT LIGHT BULB

31*

W300-0086

NIGHT LIGHT LENS

32*

W300-0135

TOPAZ GLASS

TERMINAL KITS

REF NO.

PART NO.

DESCRIPTION

14

GDI-226

TERMINAL

VENT KITS

REF NO.

PART NO.

DESCRIPTION

2-3" DOUBLE PLY ALUMINUM LINER-INLET AND EXHAUST:

15*

GDI-320KT

VENT KIT 20FT

15*

GDI-325KT

VENT KIT 25 FT

15*

GDI-335KT

VENT KIT 35 FT 

Contact your dealer or the factory for questions concerning prices and policies on replacement parts. Normally 
all parts can be ordered through your Authorized dealer / distributor. 

FOR WARRANTY REPLACEMENT PARTS, A PHOTOCOPY OF THE ORIGINAL INVOICE WILL BE 
REQUIRED TO HONOUR THE CLAIM.

When ordering replacement parts always give the following information:
• 

Model & Serial Number of appliance

• 

Installation date of appliance

• Part 

number

• 

Description of part

• Finish

* IDENTIFIES ITEMS WHICH ARE NOT ILLUSTRATED. FOR 
FURTHER INFORMATION, CONTACT YOUR AUTHORIZED DEALER.

41.1

FAILURE TO POSITION THE PARTS 

IN ACCORDANCE WITH THIS 

MANUAL OR FAILURE TO USE ONLY 

PARTS SPECIFICALLY APPROVED 

WITH THIS APPLIANCE MAY 

RESULT IN PROPERTY DAMAGE OR 

PERSONAL INJURY.

!

WARNING

Содержание IR3GN





































Отзывы: