background image

19

W415-1034 /  09.01.11

The control module offers a remotely actuated 120V AUX 
outlet for the accent lights and a constantly powered 
120V outlet. 

NOTE: Control module ON/OFF switch should 
always be in the “ON” position. If for any reason the 
module is turned “OFF”, the components plugged 
into the module won’t have power. 

35.16

CONSTANTLY POWERED 
120V OUTLET

120V AUX OUTLET

MAINS VOLTAGE 

SUPPLY CORD

MODULE ON/OFF 

SWITCH (SHOWN IN 

THE ON POSITION)

COMMUNICATION 

BUS (3 PIN)

6.11  LOW BATTERY / MANUAL BYPASS

6.12  IN THE EVENT OF A POWER FAILURE 

6.13 CONTROL MODULE 

If the receiver is equipped with batteries they will enable fl ame height control, ON/OFF or thermostat 
function to control the fi replace during a power failure. Refer to “APPLIANCE OPERATION” section when 
communications between receiver and transmitter have been lost. The will receiver emit a “beep” sound to 
confi rm programming has been successful once power is restored. During a power failure, if the fi replace was 
on, the fl ame height will stay at the setting prior to the failure. If off when the failure occurs and then turned on, 
the fl ame height will come on at “HI”. The fl ame height can then be controlled by the remote.

35.14

The life span of the remote batteries depends on various factors: quality of the 
batteries, the number of ignitions, the number of charges to the room thermostat set 
point, etc.

When the transmitter batteries are low, a Battery Icon will appear on the LCD 
display before all battery power is lost. When the batteries are replaced this icon will 
disappear.

Not applicable when plugged into 110V.
When the receiver batteries are low, no “beep” will be emitted from the receiver 
when it receives an ON/OFF command. This in an alert for the receiver that there’s low battery. When the 
batteries are replaced the “beep” will be emitted from the receiver when the ON/OFF key is pressed.

If the batteries of the receiver or transmitter are low, the appliance can be turned on manually by sliding the 
three position slider switch on the receiver to the “ON” position. This will bypass the remote control feature and
the appliance main burner will come on if the gas valve is in the “ON” position.

35.13

76

°F

ON

Содержание IR3GN





































Отзывы: