Napoleon 9500-B Series, Руководство по эксплуатации

Страница: 2 / 76

W415-1239 / A / 03.21.14
2
IOM IOM
TABLE OF CONTENTS
1.0 INTRODUCTION 3
2.0 SAFETY SYMBOLS AND WARNINGS 4
2.1 SAFETY RULES 5
2.2 CODES 6
3.0 FURNACE SIZING 8
4.0 LOCATION OF UNIT 9
4.1 GENERAL GUIDELINES 9
4.2 OTHER CONSIDERATIONS 9
4.3 INSTALLATION IN UPFLOW, DOWNFLOW OR HORIZONTAL POSITIONS 10
4.4 AIR CONDITIONING 11
5.0 COMBUSTIBLE CLEARANCES 12
6.0 DUCTWORK 13
6.1 DUCTWORK STEPS 14
7.0 VENTING AND COMBUSTION PIPING 15
7.1 ACCEPTABLE MATERIALS IN CANADA 15
7.2 ACCEPTABLE MATERIALS IN UNITED STATES 15
7.3 VENT DRAIN OPTION 16
8.0 NON-DIRECT VENT FURNACE INSTALLATIONS USING INDOOR COMBUSTION AIR (ONE PIPE SYSTEM) 17
8.1 DETERMINING COMBUSTION AIR 18
8.1.1 CASE 1: FURNACE LOCATED IN A UNCONFINED SPACE 18
8.1.2 CASE 2: FURNACE LOCATED IN A CONFINED SPACE 18
8.1.3 CASE 3: FURNACE LOCATED IN A CONFINED SPACE, OUTDOOR AIR FROM ATTIC OR CRAWL SPACE 19
8.1.4 CASE 4: FURNACE LOCATED IN A CONFINED SPACE, OUTDOOR AIR DUCTED HORIZONTALLY 20
8.1.5 CONNECTION TO FURNACE NON-DIRECT VENT 20
9.0 VENTING GUIDELINES 21
9.1 VENT TERMINATION 22
9.2 IN CANADA 23
9.3 IN UNITED STATES 23
9.4 FURNACE VENTING INSTALLATIONS 24
9.4.1 NON-DIRECT VENT INSTALLATION USING INDOOR COMBUSTION AIR (ONE PIPE SYSTEM) 24
9.4.2 DIRECT VENT INSTALLATION USING OUTDOOR COMBUSTION AIR (TWO PIPE SYSTEM) 24
9.4.3 COMBUSTION AIR 24
10.0 TERMINATIONS 25
10.1 COMBUSTION AIR 25
10.2 EXHAUST 25
10.3 CONCENTRIC VENTING KIT 25
10.4 CONCENTRIC VENT TERMINATION INSTALLATION INSTRUCTIONS 25
10.5 LOCATION 25
10.6 MULTIPLE VENTING 26
11.0 ROUTING OPTIONS 29
11.1 EXHAUSTER ROTATION INSTRUCTIONS & PRESSURE SWITCH MOUNTING 29
11.2 CONDENSATE DRAINS 30
11.3 PREPARATIONS FOR VENT AND DRAINING OPTION 30
11.4 DRAIN HOSE INSTALLATION 34
11.4.1 DRAIN PIPING 34
11.4.2 PRIMING CONDENSATE TRAP 35
11.5 ALTERNATE CONDENSATE DRAIN PIPING INSTALLATION USING PVC OR CPVC 35
11.6 CONDENSATE NEUTRALIZERS 36
12.0 GAS SUPPLY AND PIPING 37
12.1 GAS SUPPLY 37
12.2 GAS PIPING 37
12.3 GAS INLET PRESSURE 38
12.4 LEAK TESTING 38
12.5 PURGING GAS LINES 38
13.0 CONVERSIONS 39
13.1 HIGH ALTITUDE CONVERSION 39
13.2 NATURAL TO LP GAS 39
13.3 CONVERSION STEPS 39
13.4 CHECKING THE INLET GAS PRESSURE 39
13.5 SETTING THE MANIFOLD GAS PRESSURE 40
13.6 CHECKING FURNACE INPUT 41
14.0 ELECTRICAL SPECIFICATIONS 42
14.1 ELECTRICAL WIRING AND CONNECTIONS 42
14.2 FURNACE CONNECTION 43
15.0 LOW VOLTAGE WIRING 44
15.1 THERMOSTAT LOCATION 44